Time to clean out the garage -- LOTS of stuff for sale

Motor Parts:

95 atx ECU - $50

95 atx TCM - $50

95 5spd ECU (believed to be DOA) - $10

Stock 420a exhuast manifold - $20

Brake Fluid Resevoir - $5

Brake Booster - $20


Transmision, automatic:

Built a604 for the 420a - Raybestos Race Clutch Packs and Plates, Aluminum accumulator pins, Blue Plate Special gaskets and softparts, Fairbanks Shiftkit. Tranny has ~20K miles on it, only 1/2 that was while I was turbo'd.
This originally was a $3,000 tranny, but the OD clutch hub needs to be replaced. All upgraded parts are still in excellent condition, the friction materials still grab awesome, even at 18psi. Unfortunately, the gear hub on the OverDrive Clutch hub is sheared off and needs to be replaced to take advantage of this trans.
I was quoted $300 for repair.

My loss is your gain - $300 OBO, local pick up only please (Gainesville, FL - I would be willing to meet up w/ someone 1/2 way within reason)

Upgraded Solenoid Pack - Upgrade over stock, the entire unit is physically larger and better built. Does not make the racheting sound that the stock solenoid packs make when shifting gears - $250 new, ~20K miles on it - $50

Hughes 3k+ RPM High Stall Torque Convertor - Converter is brazed w/ a strengthened sprag, special cut stator, and full needle bearings front and rear. This will be the last torque convertor you will ever need. ~3500 miles on it, and only a 2-3 hard launches. $500 new, would like to get $300 for it

Trans Cooler - B&M trans cooler, avoid the #1 killer of the a604 - HEAT. $30

Autometer Transmission Temp Gauge - 2-1/6"/52mm, Ultra-Lite Series. Out of the box, but never used. Includes Gauge and sending unit, $45 new - $25

a604 tranny fluid pan - used but in excellent condition, i originally got it as an extra that i was going to tap for a drain plug but never did - $15

OEM Replacement Torque Convertor - this is a stock replacement, stock stall speed. ~15K miles on it, still worked perfect when removed - $50

If anyone is interested in having an excellent ATX setup, I would sell EVERYTHING above listed for the atx as a package for $600. Basically, buy the atx and the high stall torque convertor, and ill throw in the solenoid pack, cooler, trans temp gauge, stock convertor and spare pan for free.


Transmision, 5spd

NVT-350, 3.94 gearing - stock 2gNT/Avenger/Sebring 5spd tranny. Complete minus Bellhousing (diff, trans case and all trans "guts" included). I never used it, but was told it was fine except reverse had difficulties going into gear when cold - $75 local pick, otherwise $100 + shipping

NVT-350, 3.94 gearing - stock 2gNT/Avenger/Sebring 5spd tranny. Complete minus bellhousing, diff and shift linkage. In need of rebuild, rounded off gears - $50 local pickup, otherwise $75 + shipping

I will sell both trannies together for $110 local pick up, otherwise $150 + shipping

(difference in price reflects the packaging needed to ship an 80lb transmission, plus the extra hassle)

NVT-350 Neon Bellhousing - will bolt up to a 2gNT/A/S as well, but is setup for the Neon's cable clutch setup - $40

NVT-350 Reverse Light Sensor and Speed Sensor - this came out of a neon, I believe they are the same in the 2gNT/A/S but I dont know that for sure - $10


Interior:

Avenger Console - entire center console, plus misc interior pieces (HVAC bezel, cruise contrl bezel, center a/c vents, dash-door vents). The inserts are all painted Blue Pearl - $50


ATX Shifter Assembly - includes the atx shift linkage - $25

ATX Brake Pedal Assembly - $15

ATX Shift Knob - Polished w/ Carbon Fiber Insert - $5

ATX Pedal Covers - Silver w/ Blue Inserts - $10



All prices do NOT include shipping. Paypal preffered, Money Orders and Cash also excepted

For local pickup I am in Gainesville, FL 32603. I am willing to meet up 1/2 way for some items, and to distances within reason (Im not going to drive 100 miles to deliver a $5 shift knob, but would definitely make the same trip to deliver a complete killer atx setup )

For anyone who doesnt know me, I am paypal verified and have a 100% positive feedback on ebay (ebay id is avengr1995). I also know a lot of people on these boards who will vouch for me.

I have pics of most items, and i can get pics of others if needed (although any new pics will have to be made with a camera phone unless I can find a friend w/ a digi)

I am flexible with pricing -- I think ive priced everything really cheap and very fair already, but I will work with you on pricing, especially if youre buying multiple items

Thanks,
Ryan McDonald
avengr1995@aol.com

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

i msged you about the mtx that has the problem going into reverse.

Does the reverse switch and speedo sensor come with wiring pigtails?

interested in autometer tranny gauge. How much plus shipping? Ill do paypal. Could you explain what exactly the high stall torque converter does?

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

Ill take the sensors

Member # 751


FOUNDER of the Central Cali chapter of 2GNT!
(I got kicked out after I refused to go Cow tiping) - Hehehe you know who this is for

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

Trans temp gauge, cooler and spare pan are sold.

Both 3.94 trannies are also currently spoken for. If that changes i will let you know.

Everything else is still available.

Thanks,
Ryan

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

/bump

Interested in the upgraded solenoid pack, what are the gains of this and how it works. I've been trying to figure it out.


*rebuild in process*
GST Muffler
injen short ram intake
magnecore 8.5mm wires
EGR removal/blockoff
front/rear strut tower bars
GSX dual piston calipers

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

can i get a pic of the shift knob? ill take it if you can garuntee that it will fit... the one i have now is loose and i cant stand it.

p.s. how do you spell *garuntee*
lol

1998 GS
Mods: Cold air intake, Ported/polished stock intake manifold, AFX 55mm TB, Pacesetter header,
Custom Magnaflow cat-back exhaust system, AFX Underdrive pulley,
B&M short throw shifter(cut/welded), Symborski Shift Kit, Solid front motor mount, Monster ground wire kit.

Status: Finally up and running!

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

Just Updating the List, Thanks



Motor Parts:

95 atx ECU - $50

95 atx TCM - $50

95 5spd ECU (believed to be DOA) - $10

Stock 420a exhuast manifold - $20

Brake Fluid Resevoir - $5

Brake Booster - $20


Transmision, automatic:

Built a604 for the 420a - Raybestos Race Clutch Packs and Plates, Aluminum accumulator pins, Blue Plate Special gaskets and softparts, Fairbanks Shiftkit. Tranny has ~20K miles on it, only 1/2 that was while I was turbo'd.
This originally was a $3,000 tranny, but the OD clutch hub needs to be replaced. All upgraded parts are still in excellent condition, the friction materials still grab awesome, even at 18psi. Unfortunately, the gear hub on the OverDrive Clutch hub is sheared off and needs to be replaced to take advantage of this trans.
I was quoted $300 for repair.

My loss is your gain - $300 OBO, local pick up only please (Gainesville, FL - I would be willing to meet up w/ someone 1/2 way within reason)

Upgraded Solenoid Pack - Upgrade over stock, the entire unit is physically larger and better built. Does not make the racheting sound that the stock solenoid packs make when shifting gears - $250 new, ~20K miles on it - $50

Hughes 3k+ RPM High Stall Torque Convertor - ERT's "Track Master" - Converter is brazed w/ a strengthened sprag, special cut stator, and full needle bearings front and rear. This will be the last torque convertor you will ever need. ~3500 miles on it, and only a 2-3 hard launches. $500 new, would like to get $300 for it

OEM Replacement Torque Convertor - this is a stock replacement, stock stall speed. ~15K miles on it, still worked perfect when removed - $50

If anyone is interested in having an excellent ATX setup, I would sell EVERYTHING above listed for the atx as a package for $600. Basically, buy the atx and the high stall torque convertor, and ill throw in the solenoid pack, cooler, trans temp gauge, stock convertor and spare pan for free.


Transmision, 5spd

NVT-350, 3.94 gearing - stock 2gNT/Avenger/Sebring 5spd tranny. Complete minus Bellhousing (diff, trans case and all trans "guts" included). I never used it, but was told it was fine except reverse had difficulties going into gear when cold - $75 local pick, otherwise $100 + shipping DEAL PENDING

NVT-350, 3.94 gearing - stock 2gNT/Avenger/Sebring 5spd tranny. Complete minus bellhousing, diff and shift linkage. In need of rebuild, rounded off gears - $50 local pickup, otherwise $75 + shipping DEAL PENDING

I will sell both trannies together for $110 local pick up, otherwise $150 + shipping

(difference in price reflects the packaging needed to ship an 80lb transmission, plus the extra hassle)

NVT-350 Neon Bellhousing - will bolt up to a 2gNT/A/S as well, but is setup for the Neon's cable clutch setup - $40 DEAL PENDING


Interior:

Avenger Console - entire center console, plus misc interior pieces (HVAC bezel, cruise contrl bezel, center a/c vents, dash-door vents). The inserts are all painted Blue Pearl - $50


ATX Shifter Assembly - includes the atx shift linkage - $25

ATX Brake Pedal Assembly - $15

ATX Shift Knob - Polished w/ Carbon Fiber Insert - $5

ATX Pedal Covers - Silver w/ Blue Inserts - $10



All prices do NOT include shipping. Paypal preffered, Money Orders and Cash also excepted

For local pickup I am in Gainesville, FL 32603. I am willing to meet up 1/2 way for some items, and to distances within reason (Im not going to drive 100 miles to deliver a $5 shift knob, but would definitely make the same trip to deliver a complete killer atx setup )

For anyone who doesnt know me, I am paypal verified and have a 100% positive feedback on ebay (ebay id is avengr1995). I also know a lot of people on these boards who will vouch for me.

I have pics of most items, and i can get pics of others if needed (although any new pics will have to be made with a camera phone unless I can find a friend w/ a digi)

I am flexible with pricing -- I think ive priced everything really cheap and very fair already, but I will work with you on pricing, especially if youre buying multiple items

Thanks,
Ryan McDonald
avengr1995@aol.com

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

will consider all offers, thanks

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

Pedal covers are spoken for

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

Solenoid pack is spoken for

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

bump

I need a manual tranny... don't suppose one's still available?

Anyone know anyone who can help me tune this in the Pittsburgh area (Greensburg)?