2GNT.com Forums - Viewing topic - G.I.- 2.5" Mandrel bent HRC Downpipes

Home Site Background Info & Specs Mods & Tech Info CAPS Part Reviews Donate 2GNT Stickers

Printer-friendly copy

0 Users in Chat

Team 2GNT Marketplace

2GNT Buy / Sell / Trade (BST)

topic #38487

View in linear mode

Subject: "G.I.- 2.5" Mandrel bent HRC Downpipes"

Previous topic | Next topic

XtremeRS	Mar-18-04 02:22 PM
Member since May 20th 2003 6329 posts,

#38487, "G.I.- 2.5" Mandrel bent HRC Downpipes"

I've had several people asking if I was still making these, and since interest is there, I am planning on doing more of them. I'd like to have at least 5 units as a bare minimum to make this worth while, and prob no more than 10 units total. All orders will need to be prepaid, and turnaround time will be 3-4 weeks after reciept of payment. Price will be 265.00 shipped to your door. You will get the following:

2 Piece, mandrel bent,2.5" aluminized Downpipe, from Turbo outlet- to cat
o2 sensor fitting welded on
8" aluminized flex section
Gaskets for the connections for the upper to lower pieces, and the
downpipe to cat
Nut/bolt hardware to fasten the two pieces
Mounting support bracket welded to the upper section to bolt to block
Installation instruction sheet
All MIG welding, and welds cleaned and inspected
NOTE: This DP will NOT include a turbine outlet flange gasket

This is what it will look like:

I'll let this go for a week or two to see if I can get the minimum:

1.
2.
3.
4.
5.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

Replies to this topic

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-18-04 02:26 PM, #1

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-18-04 02:37 PM, #2

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-18-04 07:36 PM, #3

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, PiKapp504, Mar-19-04 09:05 AM, #4

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-19-04 12:13 PM, #5

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-19-04 02:21 PM, #6

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, soulcontroller, Mar-19-04 02:53 PM, #7

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, eclipsekaiser, Mar-19-04 07:37 PM, #8

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-20-04 03:04 PM, #9

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, xEclipsE RaceRx, Mar-20-04 03:56 PM, #10

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-20-04 04:18 PM, #11

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, mitsudsr, Mar-21-04 04:24 PM, #12

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, PiKapp504, Mar-22-04 05:56 AM, #13

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-22-04 09:36 AM, #14

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-22-04 11:20 AM, #15

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-23-04 02:17 AM, #16

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-23-04 03:01 PM, #17

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-23-04 03:36 PM, #18

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, xEclipsE RaceRx, Mar-23-04 04:35 PM, #19

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-23-04 04:55 PM, #20

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, xEclipsE RaceRx, Mar-23-04 05:17 PM, #21

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-23-04 06:38 PM, #22

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 96rs-t, Mar-23-04 08:17 PM, #23

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-24-04 02:58 AM, #24

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-25-04 03:39 AM, #25

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, PiKapp504, Mar-25-04 06:26 AM, #26

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-25-04 10:50 AM, #27

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, icedout, Mar-25-04 11:33 AM, #28

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, DSMRoadster, Mar-25-04 03:25 PM, #29

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-25-04 05:20 PM, #30

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-26-04 10:34 AM, #31

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-27-04 07:17 PM, #32

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Mar-28-04 11:12 AM, #33

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-29-04 01:33 PM, #34

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, CrashedMax, Mar-30-04 12:29 PM, #35

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, soulcontroller, Mar-30-04 06:08 PM, #36

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, PiKapp504, Mar-31-04 04:10 AM, #37

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, EclipseRST, Mar-31-04 04:35 AM, #38

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Mar-31-04 12:33 PM, #39

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, jsupetran, Mar-31-04 12:41 PM, #40

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-01-04 03:03 PM, #41

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Apr-01-04 03:22 PM, #42

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, PiKapp504, Apr-02-04 03:21 AM, #43

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-02-04 03:37 AM, #44

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, injendsm, Apr-02-04 05:40 AM, #45

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 95GSEclipse, Apr-04-04 07:53 AM, #46

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 96rs-t, Apr-05-04 10:43 AM, #47

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-05-04 02:09 PM, #48

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, 96rs-t, Apr-05-04 05:59 PM, #49

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, The1Bill, Apr-05-04 09:30 PM, #50

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, freddy_00_69, Apr-06-04 06:06 AM, #51

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-09-04 12:40 PM, #52

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, HiOnPSI, Apr-09-04 01:40 PM, #53

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-09-04 05:59 PM, #54

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, HiOnPSI, Apr-10-04 08:54 AM, #55

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-10-04 06:15 PM, #56

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, HiOnPSI, Apr-10-04 08:50 PM, #57

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, soulcontroller, Apr-12-04 03:33 PM, #58

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-12-04 06:03 PM, #59

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, HiOnPSI, Apr-12-04 06:56 PM, #60

RE: G.I.- 2.5" Mandrel bent HRC Downpipes, Team

Team

XtremeRS, Apr-12-04 07:35 PM, #61

95GSEclipse	Mar-18-04 02:26 PM
Member since Sep 08th 2003 662 posts,

#38488, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 0

would you be able to do a 3inch? if not i still might be in

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-18-04 02:37 PM
Member since May 20th 2003 6329 posts,

#38489, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 1

Originally posted by 95GSEclipse
would you be able to do a 3inch? if not i still might be in

No, 3" would be even more of a PITA over 2.5". Regardless, the majority of us HRC guys run the S16g, which means that a 2.5" pipe is plenty for the power that this turbo will ever make efficiently. Plus, fitting a 3" pipe in there(esp the upper) is next to impossible, without having to have a VERY sharp bend downward out of the turbo,which will restrict flow..almost pointless..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-18-04 07:36 PM
Member since Sep 08th 2003 662 posts,

#38507, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 2

ill def pick up one of these....i dont have my stock DP and the hahn kit only goes to the stock DP. Give me like 2 weeks and ill have you your money. Email me if you want or AIM

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

PiKapp504	Mar-19-04 09:05 AM
Member since Feb 22nd 2002 290 posts,

#38522, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 0

So how soon can you get these started? I'm highly interested! I'm about to redo my exhaust and I need teh DP ASAP! Thanks!

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-19-04 12:13 PM
Member since May 20th 2003 6329 posts,

#38533, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 4

Originally posted by PiKapp504
So how soon can you get these started? I'm highly interested! I'm about to redo my exhaust and I need teh DP ASAP! Thanks!

It's going to be a little while yet, at least until I can get a minimum of 5 people to sign up and everything. After that, I will collect the money, and then order all the parts. Last time, I made the DP's to order, in the order I recieved payement. As stated above, I would like a 3-4 week turnaround time, but unless issues arise, it will usually be 2-3 weeks..just don't like to make promises and have people get impatient if something happens. It worked great doing it this way last time, and it will be the same this time around. So to get it ASAP, isn't going to be very likely. I have to order parts from 3-4 different places, get it shipped to me,and then get time to take apart my exhaust on my car, to construct them, to make sure everything fits perfectly. Its rather time consuming, but I like taking my time and doing things the right way,and not make compromises.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-19-04 02:21 PM
Member since Sep 08th 2003 662 posts,

#38538, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 5

1.95GSEclipse (mitsueclipse95gs@yahoo.com)
2.
3.
4.
5.

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

soulcontroller	Mar-19-04 02:53 PM
Donating 2GNT member 2490 posts,

#38541, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 6

those downpipes are freaking awesome BTW emoji

bump for joo.

______________________________
Matt D.
'06 Evo IX SE
'98 RS-T 13.8 @ 106.1

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

eclipsekaiser	Mar-19-04 07:37 PM
Old School 2GNTer 2375 posts,

#38549, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 7

yeah pipes are good, except for my minor problem.. emoji

-K-

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-20-04 03:04 PM
Member since Sep 08th 2003 662 posts,

#38595, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 8

come on people sign up..i want one fo these....

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

xEclipsE RaceRx	Mar-20-04 03:56 PM
Member since Jan 09th 2002 2982 posts,

#38598, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 9

I was gonna wait on this, but I might not have the chance if 5 ppl dont sign up. Once there are 5 I will pay, hows that? Can I get my name on the 2nd spot?

1999 Mitsubishi Eclipse GS 10th Anniversary OZ Edition

"Mommy financed...Mommy certified"

Check Out My Site For Pix
http://home.comcast.net/~eclipseracer/Page/Home.htm

*Done with Project: Low Comp. Rebuild. Now I have a major oil leak by my rear main seal =(*

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-20-04 04:18 PM
Member since May 20th 2003 6329 posts,

#38600, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 10
Mar-20-04 04:18 PM by XtremeRS

Originally posted by xEclipsE RaceRx
I was gonna wait on this, but I might not have the chance if 5 ppl dont sign up. Once there are 5 I will pay, hows that? Can I get my name on the 2nd spot?

Yeah thats fine. I just want the people who commit to this, have the funds to pay within a week to 2 weeks. I'm depending on people who sign up, keep their commitment of wanting one of these. I'd like at least 4-5 orders to make this happen.

1.95GSEclipse (mitsueclipse95gs@yahoo.com)
2.xEclipsE RaceRx
3.
4.
5.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

mitsudsr	Mar-21-04 04:24 PM
Donating 2GNT member 459 posts,

#38644, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 11

BUMP I got one and it came out great. Perfect fit looks nice too. I highly recomend
Patrick
96 GS
14.14 @ 96.5 mph on 8psi 8 Nov.02
HRC kit, S20G, FMIC, Howell bottom end 8.6 pistons, S-FMU, Blitz BOV, P&P head, SS valves, lots more little goodies

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

PiKapp504	Mar-22-04 05:56 AM
Member since Feb 22nd 2002 290 posts,

#38669, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 12
Mar-22-04 11:22 AM by DarkOne

I'll take one, but I don't get paid till April 8th. I get one paycheck a month and I've already spent this one. So, if you can wait to accept payment till then, I'll more than happily take one! Keep me posted!

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-22-04 09:36 AM
Member since Sep 08th 2003 662 posts,

#38691, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 13
Mar-22-04 11:22 AM by DarkOne

we just need people to sign up... come on others...its ok if you dont have the money right now...just soon....i want one of these DP's. How about we try to have people on by/and with there money on April 8th?(also my birthday 19)

1.95GSEclipse (mitsueclipse95gs@yahoo.com)
2.xEclipsE RaceRx
3.PiKapp504
4.
5.

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-22-04 11:20 AM
Member since May 20th 2003 6329 posts,

#38705, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 14
Mar-22-04 11:23 AM by DarkOne

Thats fine with me..If the only reason others are not interested at the moment is not enough money, then thats no big deal. I'm in no big hurry, so if it takes more than a few weeks to get the sign up, then so be it emoji The longer it takes to get the sign up people, the longer before they get started though..but if you guys are patient, then that is fine too.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-23-04 02:17 AM
Member since Sep 08th 2003 662 posts,

#38767, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 15

(bump)

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-23-04 03:01 PM
Member since May 20th 2003 6329 posts,

#38838, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 16

B

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-23-04 03:36 PM
Member since Sep 08th 2003 662 posts,

#38841, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 17

Come on people i know you want these.......i need a DP and i would rather buy this one then a stupid stock HRC one

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

xEclipsE RaceRx	Mar-23-04 04:35 PM
Member since Jan 09th 2002 2982 posts,

#38851, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 18

Xtreme...did you make test pipes that take place of the cat too? If so is there a way I could get that thrown into my downpipe? How much

1999 Mitsubishi Eclipse GS 10th Anniversary OZ Edition

"Mommy financed...Mommy certified"

Check Out My Site For Pix
http://home.comcast.net/~eclipseracer/Page/Home.htm

*Done with Project: Low Comp. Rebuild. Now I have a major oil leak by my rear main seal =(*

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-23-04 04:55 PM
Member since May 20th 2003 6329 posts,

#38852, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 19
Mar-23-04 04:56 PM by XtremeRS

Originally posted by xEclipsE RaceRx
Xtreme...did you make test pipes that take place of the cat too? If so is there a way I could get that thrown into my downpipe? How much

Yes! I can make one of those for you too..Just add 35 bucks= 300.00 total shipped.

I have gotten several people to get in on this now, so I am going to start to order up the parts. Just send my your payment to place your order whenever you can. I will make/ship the Pipes in order i get the payments. I will keep you updated on the progress also. So, pay me when you get the money. If more than 5 people pay me, i will make it clear that i will have to order up more parts, and the time frame to be completed on those. So basically, as of now, 4 pipes are left unclaimed.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

xEclipsE RaceRx	Mar-23-04 05:17 PM
Member since Jan 09th 2002 2982 posts,

#38854, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 20

Whats is your paypal addy? I want to try and be the first one.

1999 Mitsubishi Eclipse GS 10th Anniversary OZ Edition

"Mommy financed...Mommy certified"

Check Out My Site For Pix
http://home.comcast.net/~eclipseracer/Page/Home.htm

*Done with Project: Low Comp. Rebuild. Now I have a major oil leak by my rear main seal =(*

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-23-04 06:38 PM
Member since May 20th 2003 6329 posts,

#38862, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 21
Mar-23-04 06:38 PM by XtremeRS

Originally posted by xEclipsE RaceRx
Whats is your paypal addy? I want to try and be the first one.

Oh yeah, that would prob help.. Paypal: eclipsed4evr@comcast.net

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

96rs-t	Mar-23-04 08:17 PM
Member since Jun 04th 2003 2203 posts,

#38868, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 22

is there any problem with the bottom bolt on this pipe? i will probably join this group buy.

SoCal DSM
1996 RS-T: Under Construction
1999 GS AE: New daily driver
"USING NO WAY AS A WAY, HAVING NO LIMITATION AS A LIMITATION"--BRUCE LEE

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-24-04 02:58 AM
Member since May 20th 2003 6329 posts,

#38877, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 23

Originally posted by 96rs-t
is there any problem with the bottom bolt on this pipe? i will probably join this group buy.

Its easier to put on over the HRC kit pipe..I try to put as much clearance as possible when making the upper section, so that you have a bit more room for that bottom bolt..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-25-04 03:39 AM
Member since May 20th 2003 6329 posts,

#38965, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 24

BP

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

PiKapp504	Mar-25-04 06:26 AM
Member since Feb 22nd 2002 290 posts,

#38982, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 25

So, as of right now, you don't have ANY in stock, but as soon as you get a few more people you'll make them? I'm thinking of turnaround time once I send my payment. Thanks!

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-25-04 10:50 AM
Member since May 20th 2003 6329 posts,

#39019, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 26

Originally posted by PiKapp504
So, as of right now, you don't have ANY in stock, but as soon as you get a few more people you'll make them? I'm thinking of turnaround time once I send my payment. Thanks!

After you send payment, I expect as of now, around a 2 week turnaround time. Most of the interested people seem to be on time constraints, and I will do my best to get them out as soon as I can..just remember, these are totally custom, I have to order up parts, and take apart my exhaust setup to make these..I also don't want to just slap them together either..I take pride in my work, and am not satisfied if something isn't right.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

icedout	Mar-25-04 11:33 AM
Old School 2GNTer 3139 posts,

#39024, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 27

bump...
good product people.....worth it if you want a nice product and it won't leak like the hacked stock

2006 WW IX MR
2003 BBY EVO VIII (sold)
256.9WHP & 277.9torque
http://s90395832.onlinehome.us/forum//index.php?sid=a70942a7f65043e6c873e12dcd300692

1998 Eclipse RS --show car--

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

DSMRoadster	Mar-25-04 03:25 PM
Donating 2GNT member 3445 posts,

#39044, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 28

I'm in, give me the pay pal account. My stock hrc is pissing me off. The bottom bolt got loose and chewed away at the uderportion of the down pipe. Everytime I step on it the exhaust fumes finds its way into my car.

intricatelines.com/ -graphics and vinyls

"Tell them of us and say,
For their tomorrow,
We gave our today."
-- The Kohima Epitaph

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-25-04 05:20 PM
Member since May 20th 2003 6329 posts,

#39061, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 29

My paypal: eclipsed4evr@comcast.net

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-26-04 10:34 AM
Member since May 20th 2003 6329 posts,

#39133, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 30

BP

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-27-04 07:17 PM
Member since May 20th 2003 6329 posts,

#39247, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 31

Get those payments to me guys!

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Mar-28-04 11:12 AM
Member since Sep 08th 2003 662 posts,

#39310, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 32

I will soon...need to get money from birthday...

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-29-04 01:33 PM
Member since May 20th 2003 6329 posts,

#39411, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 33
Mar-30-04 03:43 AM by XtremeRS

BUMP

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

CrashedMax	Mar-30-04 12:29 PM
Member since Jan 22nd 2003 239 posts,

#39542, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 34

I'm not sure how long you're going to have this going but I will have the money at the end of next month. I don't care if I have to wait a while (end of summer or whatever), but I'd like to get one off you eventually.

1999 Black w/black leather GS 10th Anniversary OZ edition
5 speed
Modz:
HRC Stage 2+ 16G turbo
Viper 650.2 components
Image Dynamics IDQ12 sub
Avionixx 600.4 amp

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

soulcontroller	Mar-30-04 06:08 PM
Donating 2GNT member 2490 posts,

#39604, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 35

the downpipe is awesome. fitment is perfect, and the 2 piece makes it easy to take off when you need to.

matt you should make a downpipe update page like you did for the last groupbuy on your website. that was awesome emoji

bump for joo.

______________________________
Matt D.
'06 Evo IX SE
'98 RS-T 13.8 @ 106.1

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

PiKapp504	Mar-31-04 04:10 AM
Member since Feb 22nd 2002 290 posts,

#39622, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 36

MAtt, I will have the $$$ come April 7th. Again, let me know what's up! Also, I have an Avenger. Will the fitment make any difference since the Avengers are a little longer than the Eclipses? I just want to make sure it'll all bolt up! Thanks!

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

EclipseRST	Mar-31-04 04:35 AM
Member since Apr 17th 2002 5394 posts,

#39625, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 37
Mar-31-04 04:42 AM by EclipseRST

I'm going to hold off for now but if you can't get 5 people go ahead and add me I suppose.

____________________________
HAD: '98 Eclipse RS

HAVE: '04 Grand Prix GTP Comp G

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Mar-31-04 12:33 PM
Member since May 20th 2003 6329 posts,

#39678, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 37

Originally posted by PiKapp504
MAtt, I will have the $$$ come April 7th. Again, let me know what's up! Also, I have an Avenger. Will the fitment make any difference since the Avengers are a little longer than the Eclipses? I just want to make sure it'll all bolt up! Thanks!

Yeah, it will fit just fine.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

jsupetran	Mar-31-04 12:41 PM
Member since May 04th 2002 4359 posts,

#39679, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 39

I am looking for a part-time job within the next two weeks so I will definetly be in emoji .

-------jezreel
hrc stage 2, sfmu, ml, prokits, egt, boost gauge, apexi tt, turbo xs rfl, haydans tranny cooler, costum dp, dr. uber groundwires, dynotune fp gauge. gst muff, turbo spoiler

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-01-04 03:03 PM
Member since May 20th 2003 6329 posts,

#39824, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 40

Another bump

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Apr-01-04 03:22 PM
Member since Sep 08th 2003 662 posts,

#39828, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 41

im def buying one of these!!!i just got my kit today with the stock hahn thing....that little bastard sucks tiny as hell....def count me in...ill paypal you the money once i get it

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

PiKapp504	Apr-02-04 03:21 AM
Member since Feb 22nd 2002 290 posts,

#39880, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 42

Matt, where is the O2 welded in at? The way I've got my intercooler piping ran, my current O2 sensor rubs on the piping (just the tail end of it where the wires go in). Is there anyway you can weld the O2 bung up higher? If I have to extend the wires, that's cake.

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-02-04 03:37 AM
Member since May 20th 2003 6329 posts,

#39886, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 43

Originally posted by PiKapp504
Matt, where is the O2 welded in at? The way I've got my intercooler piping ran, my current O2 sensor rubs on the piping (just the tail end of it where the wires go in). Is there anyway you can weld the O2 bung up higher? If I have to extend the wires, that's cake.

Its pretty much around the stock location, but I can weld in it just about anywhere you need it to be..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

injendsm	Apr-02-04 05:40 AM
Donating 2GNT member 6844 posts,

#39894, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 44

i want one real bad and will definately buy one but im gonna have to wait a couple weeks before i do so i can get some other expenses paid for. but put me down for one.

www.gregsorrells.com

http://ubanimator.com>

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

95GSEclipse	Apr-04-04 07:53 AM
Member since Sep 08th 2003 662 posts,

#40044, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 45

Bump.....Im still getting one...will be sending money on april 13th

Klein567 - Ya i heard about that ticket you and Sean got.
Clint485 - Stupid chick cop...worst part was she looked like a dude.
Klein567- Thats becuase all hot cops are strippers

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

96rs-t	Apr-05-04 10:43 AM
Member since Jun 04th 2003 2203 posts,

#40159, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 46

You can count me in for one! do you start production on the pipe once you recieve the money, or are you waiting on people still?

SoCal DSM
1996 RS-T: Under Construction
1999 GS AE: New daily driver
"USING NO WAY AS A WAY, HAVING NO LIMITATION AS A LIMITATION"--BRUCE LEE

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-05-04 02:09 PM
Member since May 20th 2003 6329 posts,

#40178, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 47

Originally posted by 96rs-t
You can count me in for one! do you start production on the pipe once you recieve the money, or are you waiting on people still?

Just waiting on some payments! I don't exactly have tons of money to be buying all these parts off hand, so I need to wait for payment, and also, this gives me an idea of how much to buy, knowing how many people have actually paid for one.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

96rs-t	Apr-05-04 05:59 PM
Member since Jun 04th 2003 2203 posts,

#40203, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 48

i'll send you the money as soon as i can

SoCal DSM
1996 RS-T: Under Construction
1999 GS AE: New daily driver
"USING NO WAY AS A WAY, HAVING NO LIMITATION AS A LIMITATION"--BRUCE LEE

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

The1Bill	Apr-05-04 09:30 PM
Donating 2GNT member 2292 posts,

#40250, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 49

What about making one for the 2.4? It needs another inch of length downward, but it should be the same, otherwise. Shouldn't be hard to take measurements if you need them, either. The motor is on my engine stand at the moment.

-=B-=

Dude, Boeing called. They want their wing back.

Dark0ne95: There is a butthole on that girl that his going to feel the wrath of 23 yeras of worldwide hate.
Me: Can I put that in my sig?
Dark0ne95: GO right fucking ahead.

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

freddy_00_69	Apr-06-04 06:06 AM
Member since Aug 01st 2002 1119 posts,

#40278, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 50

Count me in also, i will be paying this week.

99 RS-T
"New bottom end(8.6:1 w/long rods)"
Turbonetics 60-1/Portfueler/etc!!!!!

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-09-04 12:40 PM
Member since May 20th 2003 6329 posts,

#40655, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 51

bump

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

HiOnPSI	Apr-09-04 01:40 PM
Member since Mar 29th 2002 2745 posts,

#40659, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 52

Matt,
I need to ask you a few questions first and if you can fulfill them then add me to the list. I need another o2 bung welded for wideband and it needs a plug for now if you can find one and/or willing to do this let me know. Also, get me a final price and i'll give you a heads up if i'm interested. Thanks.

Jon

1997 Eclipse RS

13.887@104.648 5/30/03

www.haiokuracing.com

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-09-04 05:59 PM
Member since May 20th 2003 6329 posts,

#40675, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 53

Originally posted by HiOnPSI
Matt, I need to ask you a few questions first and if you can fulfill them then add me to the list. I need another o2 bung welded for wideband and it needs a plug for now if you can find one and/or willing to do this let me know. Also, get me a final price and i'll give you a heads up if i'm interested. Thanks.

Yes, for an extra 10 bucks, I can weld in a second o2 bung. I can put it anywhere you would like also. If I can find the right thread/pitch bolt, I can plug the hole too. Your price would be 275.00 shipped.

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

HiOnPSI	Apr-10-04 08:54 AM
Member since Mar 29th 2002 2745 posts,

#40708, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 54

Thanks, and 30 for the downpipe would make 305 shipped? or is it 35? I can't remember. Let me know, and i'll get you the money next week!

Jon

1997 Eclipse RS

13.887@104.648 5/30/03

www.haiokuracing.com

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-10-04 06:15 PM
Member since May 20th 2003 6329 posts,

#40739, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 55

Originally posted by HiOnPSI
Thanks, and 30 for the downpipe would make 305 shipped? or is it 35? I can't remember. Let me know, and i'll get you the money next week!

Jon 1997 Eclipse RS 13.887@104.648 5/30/03 www.haiokuracing.com

It's 275 shipped for the downpipe and 2 o2 bungs...2.5" turbo to cat..did you want a test pipe too?? dont know where you got 30 from lol..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

HiOnPSI	Apr-10-04 08:50 PM
Member since Mar 29th 2002 2745 posts,

#40752, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 56

Must have been reading something somewhere else lol.
Yeah, i want a testpipe too.

Jon

1997 Eclipse RS

13.887@104.648 5/30/03

www.haiokuracing.com

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

soulcontroller	Apr-12-04 03:33 PM
Donating 2GNT member 2490 posts,

#40894, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 57

sweet.

______________________________
Matt D.
'06 Evo IX SE
'98 RS-T 13.8 @ 106.1

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-12-04 06:03 PM
Member since May 20th 2003 6329 posts,

#40906, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 58

Alright, I'm setting a cutoff date for payments for the end of April. After that, I dont plan to make any more DP's for quite some time. I just have way too much to do in my personal time to keep making more of these. So, who ever pays for a DP up to the end of April, you get one.

265.00 shipped
Paypal- eclipsed4evr@comcast.net

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

HiOnPSI	Apr-12-04 06:56 PM
Member since Mar 29th 2002 2745 posts,

#40909, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 59

matt, can i get a final total price, including a testpipe?

Jon

1997 Eclipse RS

13.887@104.648 5/30/03

www.haiokuracing.com

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

XtremeRS	Apr-12-04 07:35 PM
Member since May 20th 2003 6329 posts,

#40912, "RE: G.I.- 2.5" Mandrel bent HRC Downpipes"
In response to Reply # 60

Originally posted by HiOnPSI
matt, can i get a final total price, including a testpipe?

Just make it an even 300.00 shipped for both. That includes your second o2 fitting also..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Report This Post to Admin

Printer-friendly copy | Reply | Reply with quote | Top

Top

Team 2GNT Marketplace

2GNT Buy / Sell / Trade (BST)

topic #38487

Previous topic | Next topic

Powered by DCForum+ Version 2.2
Copyright 1997-2005 DCScripts.com, Copyright 2005-2026 2gnt.com

Generated in 0.123 seconds, executing 136 queries.