I know that the Walbro FP and FMU can be installed before installing all the other turbo parts. I was told you can also do that with the Missing Link. I just installed the Missing Link and 1st start up the car rev up... then drop low rpms and began to want to shut off then it shut off. 2nd start up, car rev up, drop low rpms then began staying around 800-900. I needed to go to Publix so decided to see if anything would happen... well around 4,300-4,500 rpms I felt a lack of hp and the car began feeling like it was choking. So I took off the Missing Link and the car is running like it was running before. Was I suppose to install this after hooking up all the rest of the turbo parts? I didn't hear any vaccum leak, just the little hole on the side of the missing link sucking in air.

Decided to re-intall it and make sure everything is tight. The idle did the same thing, rise, lope, drop and come back up to 900-1,000 rpms. Turned the car off, turned it back on and it started acting like it wanted to shut off then it jumped idle and stay at 900 rpms. So I decided to take it for a test drive. 2nd gear I hit 4,000 rpms and it felt like I hit fuel cut and the car started to choke up and didn't want to go anywhere till I let off. So turn around went home took off the Missing Link and the car is idling fine, took it for a drive... 2nd gear 4k was running fine... took it 4.5k 2nd gear running fine. Did I buy a faulty Missing Link?

-Chris
1999 Eclipse T-GS


2.4 Project is Officially underway

Hmmm... so then I can assume I was sold a bad Missing Link? Should I go with a FCD then? I mean what would be the logical thing to do for this situation. I'll be contacting the person I bought it from. I can only assume its bad because of the way my car was acting with it on and taking it off the car ran fine again.

Yeah, that is what I would do.

-Chris
1999 Eclipse T-GS


2.4 Project is Officially underway

Thank you for the help! I already contacted him. Looks like the FCD is the way I'm going then for my setup 97 Eclipse RS and my girlfriends 99 Eclipse RS.

yea a homemade voltage clamp is best . but ur problem with the missing link is 2 things . 1st you have to put a filter that comes with the missing link in the lttle hole. without it its like a vac leak and it will do exactly what u said it was doing . 2nd after installing the ml u need to reset the ecu

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

you can trim down a cigarette filter and use it

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

My missing link sounded the same way, i could hear the whistle out the side of the hole, then realized the filter is supposed to go in the side.....works just fine, make sure you have everything installed right

its supposed to go in the small hole on the side not inside the ml .a tiny filter maybe a 1/4'' long . thats definitly y its not working right .

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

boosted60trimrst thanks a lot! I just installed it and took it for a test drive and its idling and running fine. Hopefully when its boosted the ml does its job. Thanks again!!! Points given!

You can also trim some of the seat foam from the bottom of the back seat and use that too. Or go with megasquirt and not use anything?