#93843, "RE: What size fitting is this? (pic inside)" In response to Reply # 7
OK... I have to help... I have extensive knowledge in this subject It's just that I work w/ hydraulic fittings everyday...not trying to brag.
Mike D: The fitting is a male to male union (lol) with -8 AN to 7/8 straight thread. I see you have an o-ring or some kind of gasket around the nut on the straight thread side, make sure whatever you are installing that side into has a chamfer around the top of the thread. That is what the o-ring side would seal against.
Baxsom: memory check was close, but 3/4 is -12AN
Wickedesi: measuring the inner diameter is not how you tell what size fitting you have because higher pressure fittings have thicker walls, i.e. less inner diameter. The way you tell is by measuring the mating tube outer diameter.
So a male -4 AN fitting will connect to a tube with the O.D. of 4/16 or 1/4 or .250 whichever way you want to look at it
Some companies refer to AN fittings differently, so if you guys are buying some fittings for our cars AN just stands for ARMY NAVY, catchy huh, some places like Parker call them JIC or SAE 37 deg fittings.
Please E-mail me (bahhaha@yahoo.com)or PM me with any of your hydraulic fitting questions, I'll be glad to help. Also I will post a chart and a shadow diagram to help you figure out what fittings you have.
Sorry for the long post, just tried to cover everything.
#93844, "RE: What size fitting is this? (pic inside)" In response to Reply # 8
Originally posted by bahhaha OK... I have to help... I have extensive knowledge in this subject It's just that I work w/ hydraulic fittings everyday...not trying to brag. Mike D: The fitting is a male to male union (lol) with -8 AN to 7/8 straight thread. I see you have an o-ring or some kind of gasket around the nut on the straight thread side, make sure whatever you are installing that side into has a chamfer around the top of the thread. That is what the o-ring side would seal against. Baxsom: memory check was close, but 3/4 is -12AN Wickedesi: measuring the inner diameter is not how you tell what size fitting you have because higher pressure fittings have thicker walls, i.e. less inner diameter. The way you tell is by measuring the mating tube outer diameter. So a male -4 AN fitting will connect to a tube with the O.D. of 4/16 or 1/4 or .250 whichever way you want to look at it Some companies refer to AN fittings differently, so if you guys are buying some fittings for our cars AN just stands for ARMY NAVY, catchy huh, some places like Parker call them JIC or SAE 37 deg fittings. Please E-mail me (bahhaha@yahoo.com)or PM me with any of your hydraulic fitting questions, I'll be glad to help. Also I will post a chart and a shadow diagram to help you figure out what fittings you have. Sorry for the long post, just tried to cover everything.
Bingo. wow. good stuff there.
......................................................................................................................... Built. That's All... ......................................................................................................................... www.monkeybuttpirate.com ......................................................................................................................... 2 Fingers of Scotch with a milk back... Stat!
#93845, "RE: What size fitting is this? (pic inside)" In response to Reply # 9 Mar-15-06 04:07 PM by bahhaha
Everything you need to know about fittings, compliments of Parker.
Pay attention to the section "Fitting End Size" Pg. 11 of that section shows the shadow chart I was talking about If you print it out on an 8x10 and line up your fittings to the paper you can figure out which one you have. It's one of the bookmarked tabs
#93849, "RE: What size fitting is this? (pic inside)" In response to Reply # 10
Originally posted by bahhaha Everything you need to know about fittings, compliments of Parker. Pay attention to the section "Fitting End Size" Pg. 11 of that section shows the shadow chart I was talking about If you print it out on an 8x10 and line up your fittings to the paper you can figure out which one you have. It's one of the bookmarked tabs http://www.parker.com/tfd/cat/pdffiles/W-ANI.pdf
Search
Printer-friendly copy
5 Users in Chat
