Well, apparently my buddy went to Nopi in St Louis and apparently talked to someone from HAHN and there was a HAHN car there.

They showed him the engine compartment for a brief second. Guess what was installed... An 8 injector setup. Complete bolt on kit from HRC.

My buddy was told that the kit will be available very soon and they were just waiting on some patent work to be completed and the kit would range anywhere from $500 to $700.

Again, this is supposidly a complete bolt on kit with no holes to drill.

The HRC rep apparently was going on and on about how well they have tweaked this system with outstanding results.

Well.. I trust my friend and what he says, however.. Who knows. Its all speculation till we see something new.

James

Reminds me of this thread:

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=8&topic_id=73549&mesg_id=73549&listing_type=search

__________________________________________
~Chris
03 SRT-4

__________________________________________
~Chris
03 SRT-4

ahhhhhh

Originally posted by babybeclipse

Originally posted by Uberingram

Originally posted by siueclipse

Originally posted by Uberingram Reminds me of this thread: http://forums.2gnt.com/dcboard.php?az=show_topic&forum=8&topic_id=73549&mesg_id=73549&listing_type=search

Just give me the jist of it.. hehe

Originally posted by XtremeRS Exactly. You try putting in those large of injectors on our car and see how it runs!!! I mean hell, we have to run like 10-15 psi of fuel pressure on 440's alone, and even still its rich as hell just using a FPR..I and also a few others heard Len say what size injectors he was using, its no huge secret. I don't care what anyone says, you put in some big ass injectors and try to make the car run with just a FPR. It's not going to happen, which is why i say he is not telling *anyone* about his *secret* part he is using. I will bet a very good amount of money it's the same *FICU* or whatever part HRC is trying to use on their kits. Its basically a pulse width converter of sorts..stock injector pulse width into the unit, and modified lower pulse width out. Its pretty simple and can be hidden very easily. I swear, I have no clue why people are keeping this stuip shit a big secret.

Here we go again...

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

can we just end some petty debate. its not going to ever go anywhere

__________________________________________
~Chris
03 SRT-4

Anyone with interest in this is welcome to contact me. I am completely uninterested in arguing the merits here. No offense to the 2GNT faithful who have frequented this forum for years, but events of the past year or so have put things in a completely different light for us regarding information on new ideas.

Best bet is to email me with your 2GNT handle and let me know a phone number and a good time to call you. All I ask is that you be sincere in your intention to upgrade your fuel system, as the calls we can process limits me to serious inquiries only at this time.

Fuel It!
Bill

I personally have a lot of trust in what HRC does and says. They are pioneers when it comes to the 420a motor. Ill follow their lead anywhere.

Peace
James

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

_ _ _ _ _ _ _ _ _

96 Black ESi
91 Red TSI AWD (RIP)
02 WRX


"turnin wrenches for nine hours in the pouring rain, just to get the beast up and running again"

Aerospace Certified TIG welder for Precision Castparts in Portland, OR.

JoshSpair.com

_ _ _ _ _ _ _ _ _

96 Black ESi
91 Red TSI AWD (RIP)
02 WRX


"turnin wrenches for nine hours in the pouring rain, just to get the beast up and running again"

Aerospace Certified TIG welder for Precision Castparts in Portland, OR.

JoshSpair.com

i wouldnt doubt it really.
they probably got their hands on the 034 and made one of their own slightly different so they could patent it. if you think about it all they need to do is make a lower intake and it is a bolt on affair for the most part.

Terry

96 Eagle talon ESI
Star Stage II - Boost/oil/EGT gauges

97 Eclipse
Greddy header - Apexi N1 3" exhaust - SFMU/return line - Apexi SAFC - Stage 2 6 puck Sprung hub MIBA clutch - Shortened shifter - Koni Yellows w/eibach prokit - Stillen Fr/Rr swaybars - ceramic intake - DEI Keyless entry alarm - Niche 17" Shoks

Waiting to be installed: HKS EVC IV, 450 Turbo injectors, GSX Front brakes (need rotors)

Mitchell on Demand copies available

getty up

-kent-




'98 Talon...gone, but not forgotten

well thats kinda what i was thinking.....the 034 plus some of their own added features designed in and base maps for all the injectors they sell or maps based on specs. would really make the fuel system upgrade easier for most myself included.

If i was buyin i would stop down there and talk to bill maybe place an order but a few other things are comming up right now.

Terry
96 Eagle talon ESI
Star Stage II - Boost/oil/EGT gauges

97 Eclipse
Greddy header - Apexi N1 3" exhaust - SFMU/return line - Apexi SAFC - Stage 2 6 puck Sprung hub MIBA clutch - Shortened shifter - Koni Yellows w/eibach prokit - Stillen Fr/Rr swaybars - ceramic intake - DEI Keyless entry alarm - Niche 17" Shoks

Waiting to be installed: HKS EVC IV, 450 Turbo injectors, GSX Front brakes (need rotors)

Mitchell on Demand copies available

I would prefer it to come out, not work, get revised three million time before it does work and complain about it......Thats the american way lol

Terry

Originally posted by Michael_97RS

Originally posted by siueclipse Well, apparently my buddy went to Nopi in St Louis and apparently talked to someone from HAHN and there was a HAHN car there. They showed him the engine compartment for a brief second. Guess what was installed... An 8 injector setup. Complete bolt on kit from HRC. My buddy was told that the kit will be available very soon and they were just waiting on some patent work to be completed and the kit would range anywhere from $500 to $700. Again, this is supposidly a complete bolt on kit with no holes to drill. The HRC rep apparently was going on and on about how well they have tweaked this system with outstanding results. Well.. I trust my friend and what he says, however.. Who knows. Its all speculation till we see something new. James

Just for the hell of it I'll stoke a fire. Are you sure yoru friend didn't see a direct port nitrous setup? You said he only saw it for a second... Patients is a virtue gentleman. Would you rather have a product released and untested. Then revised a dozen times in the first month it's out, or get a product tried, tested and ready to go. Products coming out of HRC have to come out of the box excellent because the eyes are on them. Anything released will be scrutinized under a microscope. That's he problem with being the best company to turbo the 420A. Anything Bill does or thinks of doing will be front page news in a dozen forums on the internet. Exile Racing Technologies: http://www.exileracing.com So. All that's left, is... everything - Jesse James

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Megasquirt powered 420A
Custom turbo system

http://www.ms-custom.com

the car my buddy saw was the neon

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Megasquirt powered 420A
Custom turbo system

http://www.ms-custom.com

Originally posted by MrSlick

Originally posted by siueclipse the car my buddy saw was the neon

Hmmm... well that changes things... For a start any intake or 8 injector bolr on setup would be different for the Neon... Is it the same Hahn Neon that has the Quad Throttle Body setup on by chance???

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

My computer techie staff member (a part-time intern) who would upload the info to the site was unable to come in today. But I promised to get you the info today, so here goes. I will ask that you all make an exception and pardon this ad pitch on this board, for what you see below is definitely advertising oriented, not what I would typically post here, but I feel it is appopriate to do this under the circumstances. This is the same exact info we will post to the site ASAP. For those of you who have questions, please call me or email me, as I don't want this to turn into a full-blown 'sales thread':
630-553-6830 x 2
eng@turbosystem.com

=============================

Breakthrough! The Revolutionary New PortFueler for Hahn RaceCraft Turbosystem Stages IV and V

Hahn RaceCraft is proud to bring you PortFueler! This new innovation will inject that extra power you crave into your Hahn Racecraft turbosystem. This revolutionary fuel alternative allows you to bolt on a complete set of boost enrichment injectors, yet have those injectors in the ideal position at each intake port. Using the PortFueler, you can achieve up to 400 HP from the Super 16G that came with your Hahn turbosystem. With a Super 20G, almost 500 HP is possible!

Bill Hahn Jr, the leading pioneer in the development of the 420A DOHC engine, has brought his 25 years of turbosystem experience to bear on this exciting new system. Using the same staged injection concept as PortFueler, Bill has won numerous National Championships, while setting innumerable records. He has now brought this high HP fueling capability to the average enthusiast. From design, to testing, to final calibration, Bill has sweated all of the details. The results are what you would expect!


Easy to install

A complete PortFueler system only takes several hours to install with simple hand tools. Wiring chores are minimal, with only six wires to attach. No machining or welding needed. Once installed, you will have up to 27 PSI boost capability. Just fire the car up, set idle fuel pressure, and drive…Bill has done the hard work for you, no further tuning is necessary*!


Easy to live with

With PortFueler, your stock computer still controls your stock injectors. As a result, PortFueler is unmatched in all those aspects that make a street car enjoyable…your car will start, idle, and cruise as smooth as stock, with stock emissions and fuel mileage, and NO ‘check engine’ lights. Your car loves it! But when you lay into the pedal and boost occurs, PortFueler takes care of the rest.


There’s no comparison…

If you’ve ever tried to make an FMU (variable rate of gain) regulator run with big injectors at high boost, you can forget about all those frustrating issues with PortFueler. PortFueler idles @ 50 PSI, not a low 20 PSI or less where fuel injectors just can’t spray well. And the maximum fuel pressure in a PortFueler system, even at 25 PSI boost, is 75 PSI, not the insane 100+ PSI you might see with an FMU in such a high boost application. This can seriously reduce stress on components, eliminating high-pressure related failures of injectors, lines, pumps, and even the stock ECM due to excessively high fuel pressure combined with big injectors and an FMU.

And as far as pinpoint calibration for every possible boost and RPM point, PortFueler blows the FMU concept away for high boost cars. PortFueler is calibrated at almost 1000 different points, where the ‘best’ FMUS can only be calibrated at 4 different points, with the remainder of the fuel curve left to vague ‘slopes’ caused by the overlapping methods of adjustment. PortFueler adds to your turbo car the fuel mapping capability of a complete programmable engine management system at a fraction of the cost! Why limit yourself to a device that is about as adjustable as a carburetor when you can go PortFueler instead?


Can be tuned for custom applications

Should you decide you would like to adjust the internal calibration of your PortFueler, a software interface program is also available. It is compatible with Win 95, 98, 2000, NT, ME and XP. Any desktop or laptop PC can talk to PortFueler.


Contains everything you need

Here’s what you get in a complete Stage IV or V upgrade package:

PortFueler injector mounting system
Four ACCEL high performance fuel injectors
PortFueler control module, pre-calibrated for your application
1:1 Aeromotive fuel pressure regulator
All needed lines, fittings, and hardware
Expert guidance on how to set up other aspects of your car for this new power level
Detailed installation instructions

Call today to enter the next level of high performance turbo tuning: PortFueler!

*: Our calibrations are based upon a stock head, cams, and valves, stock intake, HRC turbosystem, aftermarket exhaust. You may need to recalibrate PortFueler if your application varies from this configuration.

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

HELL YES...

Sounds like a great system. I will be going this route soon. You forgot to mention the price sir...

Nick
97RS

turbo8u> shut your SUCK
ZAO684: NIPPLE warning...maybe>?
turbo8u> yea i was a window licker on the short bus in junior high

PM me - who builds your additional injector controller? Just wondering if its in-house or a 3rd party.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

yahoo's!

Steve-o
Top secret.

Originally posted by FlyinEsi
I guess I'll just have to live with a 500+ hp AWD 4-banger.

Bill, I sent you an email through the board (unrelated to the fuel setup but sales related).

-"Easy Mac"
05 Mazda RX-8 (RR8 #88)
99 Eclipse RS 398whp & 372lb-ft

Price???

Under a thousand hopefully...

-------jezreel
1998 GS with hrc stage 2, sfmu, ml, prokits, Greddy warning gauges: egt, boost gauge, and oil pressure, apexi tt, haydans tranny cooler, costum dp, groundwires, dynotune fp gauge. gst muff, turbo spoiler
Boostin since Aug 03.

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting

Under 1000. OMG. I really hope its not that much. I'm not tryin to be an ass, but 8-injector setup seems like the same thing, with a little more fabrication involved. You could technically do this with a spacer plate between upper an lower manifold with injectors mounted to it, bolt on, and easy. The tuning part seems to be what they take care of with base settings. Is there more to it, or am I missing something? Nonetheless still good work, long time comming.

Work in progress
98 GS t3/t04e, hrc Sidemount, tial 38mm, HKS ssq bov, clutchmaster stage 4, wiseco pistons, Eagle rods, Apexi TT, HKS EVC II, Phantom grip lsd, 3in turbo back, Eibach pro-kit, Defi D-gauge EGT,boost, autometer fuel pressure
8-inj setup in the works, HKS AIC III and 450cc injectors

Thanks for sharing details with us Bill.

There are some details missing though... like how do the injectors attach to the existing intake? My guess is a spacer between the upper and lower intakes? Am I right?

Personally I'd be very surprised if this unit is under $1000... maybe just under it but if you add all the parts included you have way over $500 for starters...

This is a good solution for some I am sure... but it still does not offer the precise control that a 4 injector setup can like a DFI or Megasquirt setup... sorry but there is no way to have a perfectly smooth transistion from non-boost into boost using 8 injectors with the stock 4 still controlled by the stock ecu...

Also, I don't see anything about intake air temp sensors in your post... without knowing the intake air temp you cannot ensure you do not go lean without making the mix slightly rich to compensate for different intake air temps...

But I'll stop digging into the technical facts right now... This is a good solution for most of the users out there...

One question though, does it have an input for a wideband o2 sensor?

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Megasquirt powered 420A
Custom turbo system

http://www.ms-custom.com

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

EDIT: well since i made a useless post already i guess i'll edit it into a question even though you said to call

I have the stage 2 turbo kit with fmic and je pistons w/ crower rods. Also, it is a s16g turbo. What size injectors would come in the kit and if I can get a more precise price I will probably be able to place the order within the next 2 weeks. (if it is indeed available now) Also I already have 42lb ford injectors that I was planning on using with a SFMU. Would I need to sell them and use what you supply or will they work without having to do any tuning?

Sorry... I figured I would make something out of this post since all it said was oops b/c i am dumb

Originally posted by CarbonFiberRST
EDIT: well since i made a useless post already i guess i'll edit it into a question even though you said to call I have the stage 2 turbo kit with fmic and je pistons w/ crower rods. Also, it is a s16g turbo. What size injectors would come in the kit and if I can get a more precise price I will probably be able to place the order within the next 2 weeks. (if it is indeed available now) Also I already have 42lb ford injectors that I was planning on using with a SFMU. Would I need to sell them and use what you supply or will they work without having to do any tuning? Sorry... I figured I would make something out of this post since all it said was oops b/c i am dumb

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

Can we buy just the "spacer"? Many have a somewhat similar setup, and just need a permanent way to mount the extra injectors, aside from drilling/bosses.

Work in progress
98 GS t3/t04e, hrc Sidemount, tial 38mm, HKS ssq bov, clutchmaster stage 4, wiseco pistons, Eagle rods, Apexi TT, HKS EVC II, Phantom grip lsd, 3in turbo back, Eibach pro-kit, Defi D-gauge EGT,boost, autometer fuel pressure
8-inj setup in the works, HKS AIC III and 450cc injectors

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

I can add this:

Fact is, we will be showing it 'in the flesh' on our website later this week, and 'in person' at the DSM Shootout.

Bill Hahn Jr.
98 RS Turbo: 10.87 @ 136 MPH
HRC Stage V with N20
Nation's Fastest Street FWD 2G DSM
www.turbosystem.com

As soon as I receive my kit, I will post a FAQ on the install if thats cool with Bill.

James

Damnit.

__________________________________________
~Chris
03 SRT-4

Wooooot the most kickass 2gnt at the shootout (grrr and i cant make it!!!)

:thumb

Bill im actualy geting interested in your system

vote for your choice of body style for Bluie!! http://www.cardomain.com/id/bluemooneclipse

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Megasquirt powered 420A
Custom turbo system

http://www.ms-custom.com