Where can i find one of these. Hrc put the bov flange in the wrong place. It points towards the ecu and fuse box. I need help ASAP!!

Mods: JE8:8:1 pistons,Eagle Rods,fully built head w/1mm Rev valves,crane titanium springs and retainers,ported and polished head and intake mani,Hrc2 turbo kit,sfmu,safc,turbo xs dual stage boost controller,turbosmart megasonic,Fluidyne radiator,160deg thermo,spec stage 3 clutch,aem front and rear big rotors,3" hahn dp 3" back exhaust,stage 2 axles,and the list goes on

Pics??

what do you mean wrong angle? the BOV mounting point should point straight up towards the hood when the pipe is installed correctly.

anyway...

here ya go...

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=33742&item=2476104601&rd=1

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

it will work unless you got some basterdized pipe. what BOV you using? my ECU is even pushed forward cause my the MSD.

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

i am using the rfl and from what my friend said is that is is pointing towards the ecu and fuse box. He knows alot about turbo parts and stuff and i trust him when he says it wont work

Mods: JE8:8:1 pistons,Eagle Rods,fully built head w/1mm Rev valves,crane titanium springs and retainers,ported and polished head and intake mani,Hrc2 turbo kit,sfmu,safc,turbo xs dual stage boost controller,turbosmart megasonic,Fluidyne radiator,160deg thermo,spec stage 3 clutch,aem front and rear big rotors,3" hahn dp 3" back exhaust,stage 2 axles,and the list goes on

i have the hrc kit, and the rfl. mine works fine.

tell your friend to try it anyway, i thought the same thing before i got it all bolted up, that it wasn't going to work, but obviously it does. so...go look your self or make him SHOW you it wont work. if its a true HRC pipe, it WILL work.

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

It is a true hrc pipe and it will not work but i found a rad. hose bent in a 90 and used that until my turbo xs 90 comes in

Mods: JE8:8:1 pistons,Eagle Rods,fully built head w/1mm Rev valves,crane titanium springs and retainers,ported and polished head and intake mani,Hrc2 turbo kit,sfmu,safc,turbo xs dual stage boost controller,turbosmart megasonic,Fluidyne radiator,160deg thermo,spec stage 3 clutch,aem front and rear big rotors,3" hahn dp 3" back exhaust,stage 2 axles,and the list goes on

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

__________________________________________
~Chris
03 SRT-4

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

well like i said i tried everything to make it fit but i had to make a 90 bc the flange was put like 2 or 3 inches further down from your flange TIM!! And i know alot about turbo stuff to its just that he was installing everything b/c i have to work all the time and i didnt have time to go by there and check it out til the next day

Mods: JE8:8:1 pistons,Eagle Rods,fully built head w/1mm Rev valves,crane titanium springs and retainers,ported and polished head and intake mani,Hrc2 turbo kit,sfmu,safc,turbo xs dual stage boost controller,turbosmart megasonic,Fluidyne radiator,160deg thermo,spec stage 3 clutch,aem front and rear big rotors,3" hahn dp 3" back exhaust,stage 2 axles,and the list goes on

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)