Well I got a fatty commission check and bonus this month so I can finally get a SFMU, Walboro 255 and 30# injectors. Can anyone recommend a shop in the Milwaukee/Chicago area where I can get these installed. Once this is done, it's time for me to shop for a new block to rebuild

I called around local shops and do not one any of these deeks installing my stuff. Most of them I have to buy the parts there to have them install it, and none of them carried Vortech. F-That!

1999 Black w/black leather GS 10th Anniversary OZ edition
5 speed
Modz:
HRC Stage 2+ 16G turbo
Viper 650.2 components
Image Dynamics IDQ12 sub
Avionixx 600.4 amp

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

Put that stuff in yourself man and save like 300 bucks. All of those items are easy as pie to put on. If you run into problems, just ask in here. You know someone will help you...


1996 Eclipse RS / 5-Speed / Aerogear Body / Coated in Magnetic Red Metallic rev.2 / T3 Turbo Intercooled @ 8 psi / More at http://home.insightbb.com/~mgalyan/
Mark Galyan - Indianapolis, Indiana

Do that sheet yourself, its easier then wipin your own ass!!

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

yeah dude. it seemed really hard at first but its EASY!!! just take a weekend off starting on friday and well walk you through. also check out whodatt's write up on the mods page up top where the site advertising banner is.

-------jezreel
hrc stage 1, sfmu, ml, prokits, egt, boost gauge, apexi tt, costum dp, dynotune fp gauge. gst muff, turbo spoiler


:o

I live in Green Bay, I'll help you put this stuff on for free if you drive up to my house in Green Bay. I have a turbo GS as well, but with the 8inj setup. Also I have a heated garage. Everyone else is correct, don't waste the money for sin=me shop to install this stuff, as it really isn't very hard and shouldn't take very long either.

I know I could do it I'm just a little leary about installing fuel components. All I've worked with is intakes, exhausts, brakes, and regular maintenance. Also it seems everytime I work on my car something goes wrong (like my tap breaking off in the manifold when I was tapping the hole for my EGT gauge). I always come out on top at the end but I'd rather not F anything up when it comes to the fuel.

Anyone have a writeup on a Cartech -> SFMU install? I know it that can't be hard, it's just the injectors I'm a little worried about.
Well CrashedMax's 1-Car Garage Performance shop may be open soon, thanks for the inspiration guys!

1999 Black w/black leather GS 10th Anniversary OZ edition
5 speed
Modz:
HRC Stage 2+ 16G turbo
Viper 650.2 components
Image Dynamics IDQ12 sub
Avionixx 600.4 amp

1999 Black w/black leather GS 10th Anniversary OZ edition
5 speed
Modz:
HRC Stage 2+ 16G turbo
Viper 650.2 components
Image Dynamics IDQ12 sub
Avionixx 600.4 amp

Go to Carquest if you have one, and buy an intake manifold gasket set. You need to pull the upper manifold piece off to get to the fuel rail and injectors. You shouldn't reuse gaskets ever, and this set comes with both the upper and lower gaskets for 8 bucks. Thats all you really need to buy. (We just did this stuff like 2 weeks ago.) Well actually go and pick up some Teflon Pipe paste (not tape). Sometimes called Pipe Joint Compound. Put this on all threaded fuel connections. Makes a better seal.

1996 Eclipse RS / 5-Speed / Aerogear Body / Coated in Magnetic Red Metallic rev.2 / T3 Turbo Intercooled @ 8 psi / More at http://home.insightbb.com/~mgalyan/
Mark Galyan - Indianapolis, Indiana

are you sure that you have to pull the upper manifold? I seem to remember taking my rail off and getting the injectors out without pulling the intake mani.

amiller99rs: seriously, chicks suck sometimes
amiller99rs: like if a girl walked by and said "Hey, nice cock" and just kept going you'd smile all day about that

Double the fun.

amiller99rs: seriously, chicks suck sometimes
amiller99rs: like if a girl walked by and said "Hey, nice cock" and just kept going you'd smile all day about that

I don't pull mine anymore. You can actually get to the two 13mm bolts behind the fuel rail without taking off the upper manifold if you try. it also helps if you bend the teo tabs on the top of the rail down (the ones the injector harness is supposed to mount to) or just cut them off.. leaves more room for your hands.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

We work out of Round Lake, northern Chicago suburb, labor is currently $45/hour. e-mail me at michael@exileracing.com and I can get you a quote for labor and pricing on parts if you want also.