Dead motor, credit card, wifes approval!!!
trying to stay around 3000-3500 clams.
Cant/dont wnat to do FTY, only because of shipping costs.
What parts would you do to get the HP & Psi above? Include head, block, turbo and tranny!

Ill send a half case of beer and a twinkie to who has the best set-up info

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

Engine:
JE 8.8:1 pistons and rings (.020 over)
Crower connecting rods
ARP head studs
Mopar upper & lower gasket sets
Clevite 77 main and rod bearings
Melling oil pump

Head:
Crane springs and retainers
PT rockers and lifters
55mm TB

Turbo:
s20G turbo setup
Stainless steel lines (oil, fuel, vac, boost)
fuel system of choice
Bar & plate intercooler core 24x8x3
Silicone/fiberglass couplers
Beaded IC pipes

Tranny:
Quaife LSD
Axles
clutch of choice

Lots of TUNING!!!

^^ thats going to be more than 3-3500 bucks

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

Damn, all that for $3000-3500? If it was that easy, I think we'd all have 300hp cars by now...sorry man, try and be more realistic. And don't be cheap, it just means you'll be right back where you are now before long.

-Corey

OOPS!!! sorry, meant $4000-4500. was thinkin about 3's for other reasons...

that a better figure

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

How much are shipping costs through FTY anyway?


1996 Eclipse RS / 5-Speed / Aerogear Body / Coated in Magnetic Red Metallic rev.2 / T3 Turbo Intercooled @ 8 psi / More at http://home.insightbb.com/~mgalyan/
Mark Galyan - Indianapolis, Indiana

better, but what all do you have right now so in case you would be able to keep anything it would save on money.

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

stock motor 'cept for UPD, AEM cam gears, PT lash adj. and followers, 60mm TB, MSD DIS-2, t-too small turbo kit (need to upgrade)

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

would you be doing the work yourself, like the bottom end, or having someone else do it (assembling i mean)

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

Didn't you have cams also?

id have someone do the same work that FTY does to thier blocks, i have never pulled an engine before and would want to have it done right.

I do have cams, but they are regrinds, and im gonna go for the crane 14's

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

Tim, talk to Motofool, he will set you up fat for $4500. He should put me around 400HP for $5000.


1/4 Mile: 17.4651 | 1/4 MPH: 76.69 @ 7,000 ft
www.geocities.com/rockyourworld182/

are you in a hurry to get it done? if not, you could try and wait until HRC gets their stage 3 complete and ready for sale. then you'd be running pretty good , but you could probably buy the s16g, (not sure if you have an intercooler or not) their big intercooler, fuel system look at something with maybe 440's ? the stage 4 clutch and get the head ported and polished....do you have the exhaust done? that should either get you there or close to it for around what you was wanting spent. then you could slowly add to it.
just a thought:shrug

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

engine rebuild kit ~ $1100
- (includes Pistons, rings, rods, bearings, oil pump, rear & main seal)
machine work ~ $500 or around there depending

Big 16G turbo - $450ish (I really dont know price, just a guess)
400cc injectors or 40lb injecors, around there
- sfmu unless you already have
- 255lph fuel pump unless you have one.

since you have a turbo kit though you probably have soem stuff you already need.

no headwork is needed unless head needs to be milled or decked. head is fine the way it is (look at HRC, stock head other than springs, retainers)

however much for installation, not sure on cost. parts and machien work is around 2000-2500. then installation. thats all you really need for 300 hp. mainly just build the bottom end to handle more power. head is fine how it is unless you want to do some headwork. big 16g is enough to get you to the 300hp mark. bigger fuel injectors unless you already have them. not sure if 30# injectos is enough or not.

you can do it for that price, a lot of it would be the installation though.

"Shop smart, shop S-Mart!" ~ Ash
Member # 1523

true, he doesn't have to do the heads, i was just saying that he could do them so that so much boost wasn't needed. just depends on which route he wants to go i guess.

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

"Shop smart, shop S-Mart!" ~ Ash
Member # 1523

Also, if you dont have a front mount intercooler, id say get one from HRC, and then get some mandrel bent pipes from summit racing or jc whitney and make your own ic piping. or you could have a shop do that too and it should not cost to much to have done. forgot about the IC but if oyu already have a front mount, no need to worry then. it would be better if we had a complete list of what you already have done so we could be more specific on what else you would need.

"Shop smart, shop S-Mart!" ~ Ash
Member # 1523

yeah.

also, if your aiming for 300hp at the crank or wheels
go for the wheels!!!

Matt
a.k.a. bustrblue1
R.I.P '95 Eclipse GS
intake, exhaust, push button starter, painted interior, custom short shifter, and one shiny car!
http://www.cardomain.com/member_pages/view_page.pl?page_id=230275
^ shows what happened to my baby

so you could have a built block and not have to worry about the head? as in you could take a built block and slap your stock head on it and everything would work all gravy?

that boy K-Y
kbnkb@sbcglobal.net
talonky36 (aim)

04 srt-4 (low and slo)
96 talon esi (still broke make me an offer)

"Shop smart, shop S-Mart!" ~ Ash
Member # 1523

300 to the wheels, mang!! nunu dat crank sheeit!!!

I will do cams, springs, retainers, S/S valves to the head. No port work, yet. No flow bench around my area.
i have talked with Motofool, and will be doing some more talking with him quite soon. Just waiting to see if this other turbo deal is gonna fly first.

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

Eagle H-beam Rods $310
JE 8.8:1 pistons $435
hot tank, hone block 100
clevite bearings $200
crane #14 cams $345
crower springs and titanium retainers $210
ferrea super-flo stainless valves $375
AEM cam gears 150
total $2125

AEBS in Cali does sick port work about a grand

new total 3125

assembly should run around 500....
new grand total $3625

...engine will be good up to 600HP...good luck

-Mike