Welcome to the 2GNT Forum!
Home Site Background Info & Specs Mods & Tech Info CAPS Part Reviews Donate 2GNT Stickers
Search Printer-friendly copy 2 Users in Chat
Top 2GNT Technical Turbo/Nitrous Tech topic #52502
View in linear mode

Subject: "6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???" Previous topic | Next topic
davo345Jul-22-03 08:04 AM
Member since Jul 15th 2003
510 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52502, "6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"


          

i am reading reports that people are replacing the disk in their FMU to 8:1 ratio for a not-so-rich fuel ratio on 30lb / 310cc injectors. but a few of them are saying they are STILL running rich...could this be that the 8:1 ratio disk is only rated for 24lb injectors??? i think so. so if this were the case would a 6:1 ratio disk be a better choice for 310cc injectors? check it out:

Vortech Engineering
Vortech 8:1 FMU Recalibration Kit for Vehicles with 24 lb. Injectors
All
$30
Buy Now

Vortech Engineering
Vortech 12:1 FMU Recalibration Kit for Vehicles with 19 lb. Injectors
All
$30
Buy Now


Vortech Engineering
Vortech Universal FMU Recalibration Kit (4:1, 6:1, 8:1, 10:1, 12:1 and One Gasket Included)
All
$45
Buy Now

Vortech Engineering
Vortech 6:1 FMU Recalibration Kit for Vehicles with 30-38 lb. Injectors
All
$30
Buy Now

Vortech Engineering
Vortech 4:1 FMU Recalibration Kit for Vehicles with 38-42 lb. Injectors

this is at http://www.superchargersonline.com/product_listing_2M.asp?Cat2=fuelsystem_fmu at the bottom.

bobin' and weavin' in traffic. No other place i'd rather be emoji.



^^^^^EVERYTHING HAS TO GO.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Replies to this topic
RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, davo345, Jul-22-03 11:47 AM, #1
RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, deus_ex_avery, Jul-23-03 07:12 AM, #2
      RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, Nitrous_RS1997, Jul-23-03 07:21 AM, #3
           RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, davo345, Jul-23-03 09:21 AM, #4
                RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, Nitrous_RS1997, Jul-23-03 06:07 PM, #5
                     RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, HadesOmega, Jul-24-03 12:31 AM, #6
                          RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???, davo345, Jul-24-03 01:58 AM, #7

davo345Jul-22-03 11:47 AM
Member since Jul 15th 2003
510 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52503, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 0


          

no one wanna take this question on? emoji emoji

bobin' and weavin' in traffic. No other place i'd rather be emoji.



^^^^^EVERYTHING HAS TO GO.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

    
deus_ex_averyJul-23-03 07:12 AM
Member since Jun 30th 2003
124 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52504, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 1


          

I don't know much about turboing this engine since I just bought my eclipse. But when I was doing researchfor the turbo in my Paseo I found out that Vortech used a 12:1 setting on it's supercharged Civic SI. Given that, and the fact that you're running only 10 PSI, I would say the 8:1 would be fine. The best way to know for sure would be to go to their application pages and find a vehicle running similar boost with similar compression.

Avery

There is a difference between an argument and an assertion. This is an assertion: You don't want to fuck with Shady. The argument to follow: Because Shady will fucking kill you.

-Simon Stow, Professor of Political Science, College of William and Mary

Mods: AF/X UDP, MSD coil, MSD wires, OBX header, Custom intake, partially gutted cat, Extreme PSI exhaust, Hurst short shifter...

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

        
Nitrous_RS1997Jul-23-03 07:21 AM
Donating 2GNT member
1311 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52505, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 2


          

use the 8:1 disk with 30lb injectors to run 10psi. 6:1 will be too lean at the higher RPM's. just ask DeanoD, he ran the 6:1 at first, then switched to the 8:1 i believe. just a little info here...dont expect to run the 30lber's with just the FMU(no SAFC or SFMU) and not be REAL rich in boost, and part-throttle driving especially. my advice would be to sell your FMU, and put down the 290 bucks for a SFMU and then you can run up to 440's without any other type of fuel management "required".

1997 Silver RS
Wiseco 8.8:1 Pistons(back to low compression!)
Eagle Rods
T3/T4 Turbo
Custom FMIC
Greddy Exhaust
440's
Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

            
davo345Jul-23-03 09:21 AM
Member since Jul 15th 2003
510 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52506, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 3


          

interesting...i will have to consider that when i get the money for sfmu. but for now without any boost controller at 7 psi (i think that is what the star actuator is set at?) i assume the fmu will be sufficient and at 12:1?

dave

bobin' and weavin' in traffic. No other place i'd rather be emoji.



^^^^^EVERYTHING HAS TO GO.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

                
Nitrous_RS1997Jul-23-03 06:07 PM
Donating 2GNT member
1311 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52533, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 4


          

On stock injectors, i wouldnt run over 5psi to be safe, unless my engine was built. or i had the 2k laying around for a rebuild. thats just me though.

1997 Silver RS
Wiseco 8.8:1 Pistons(back to low compression!)
Eagle Rods
T3/T4 Turbo
Custom FMIC
Greddy Exhaust
440's
Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

                    
HadesOmegaJul-24-03 12:31 AM
Old School 2GNTer
4529 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52540, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 5


          

so what happens when you throw a SAFC into the mix? I'm really considering getting one of these because my fuel ratio is really wack right now. I'm running 10:1 on stock injectors and I get full rich at WOT but at partial throttle low boost I lean out sometimes. Now I tried it with a 8:1 on stock injectors and it was still pretty rich in lower gears but it was perfect ratio at like 4th or 5th gear at WOT. But it would lean out easily at partial throttle low boost. I'm guessing this is the point where I should be investing in a SAFC to fine tune all this stuff. ARRGHH I hate messing with fuel!


http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

                        
davo345Jul-24-03 01:58 AM
Member since Jul 15th 2003
510 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#52541, "RE: 6:1 or 8:1 recalibration kit for the Vortech FMU on 10psi???"
In response to Reply # 6


          

there is no reason why you would have to change disks with the stock fuel injectors

bobin' and weavin' in traffic. No other place i'd rather be emoji.



^^^^^EVERYTHING HAS TO GO.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Top 2GNT Technical Turbo/Nitrous Tech topic #52502 Previous topic | Next topic
Powered by DCForum+ Version 2.2
Copyright 1997-2005 DCScripts.com, Copyright 2005-2026 2gnt.com
Generated in 0.06 seconds, executing 28 queries.