FINALLY I have the car back on the street after only 2 months of total BS! I was about to through in the towel, fortunately I was able to get it all worked out and I can drive it. For how long? I don’t know.

Replaced:

Tranny (gear side) -- 400.00
Upper lower lateral control arms -- 100.00
Flywheel -- 420.00
Clutch -- 450.00
Output shaft bearing -- 60.00
Input shaft bearing -- 50.00
Quaife -- 1200.00
Axles free
Tires -- 500.00
Rims -- 1000.00
Ac/alt belts -- 40.00
Coil pack/wires/plugs -- 100.00

Total 4320.00, it’s been and expensive two months.

But the boost is so fucking good that I soon forget about the cost. I forgot how 20lbs on the highway feels and how very untouchable it is.

Ahh it's good to be back. (For now at least)

Brian

Thats exactly why I am NOT boosting my car. I can't afford all that.

>Thats exactly why I am NOT boosting my car. I can't afford
>all that.

no one said u had to jump right to stage 4

-Joe
___________________________________
White 98 Eclipse GS MT
Star Stage 2
*Stolen - 10/24/03*

With my luck, I would be breaking shit before I even got the turbo kit installed.

Cost sucks and downtime sucks but taring up modded gt Mustangs on the way home makes it all worth it.

it's great that you have your car back on the road, if you don't mind me asking what do you do for living?

why and why again did u replace all that ??

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

Congrats Brian! It's about time you got it running again!! You should swing by my house sometime and give me a ride!

If it ever warms up in this cold ass state, I'd like to work out the issues I'm having with my car so I can run about 15psi. But right now I've got an oil leak somewhere, and I still have that ticking noise that didn't go away when I replaced my lifters. I might have a flat spot on the roller of one of my rockers or something. That's probably what I'll try next.

Anyway, I could use some assistance from a Stage 4 guru!

You are not your job.
You're not how much money you have in the bank.
You're not the car you drive.
You're not the contents of your wallet.
You're not your fu**ing post count.

97 Eclipse GS - *SOLD*
01 Audi A6 2.7T
01 YZF-R6

>>why and why again did u replace all that ??

Tranny (gear side) <---because it broke, output shaft broke.
Upper lower lateral control arms -- 100.00 <----because the where making noise.

Flywheel -- 420.00 <--------because aluminum is ligher and better

Clutch -- 450.00 <------------because it broke

Output shaft bearing -- 60.00 <-----because it was clicking and broke

Input shaft bearing -- 50.00 <---because it was clicking and broke

Quaife -- 1200.00 <---------because I like LSD hahahaha

Axles free <----------They broke

Tires -- 500.00 <-----where bald

Rims -- 1000.00 <------for fun and my old ones where bent, 3 of the 4

Ac/alt belts -- 40.00 <-------because the needed it

Coil pack/wires/plugs -- 100.00 <----stock coil was cooked



>You should swing by my house sometime and give me a ride!

I hate the springs, you drive to me.

>Anyway, I could use some assistance from a Stage 4 guru!

I could try but I really dont know much about cars.

Brian

well that makes sense good work man hope u enjoy =P

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

>>>>You should swing by my house sometime and give me a ride!
>>I hate the springs, you drive to me.

Actually, I live in Highlands Ranch now, right by Park Meadows mall. I moved to Denver about 3 weeks ago.


>>>>Anyway, I could use some assistance from a Stage 4 guru!
>>I could try but I really dont know much about cars.

Yeah well, maybe you could hold the light and hand me tools then!

You are not your job.
You're not how much money you have in the bank.
You're not the car you drive.
You're not the contents of your wallet.
You're not your fu**ing post count.

97 Eclipse GS - *SOLD*
01 Audi A6 2.7T
01 YZF-R6

>
>Yeah well, maybe you could hold the light and hand me tools
>then!
>

Hey, I'm getting pretty good at that seeing as how my friend is the one who works on my car for me. It's practically his car...

____________________________
HAD: '98 Eclipse RS

HAVE: '04 Grand Prix GTP Comp G

where did u get the clutch at?? and what kind of clutch do you have i need 1 and PG

Boca Raton, Florida
95 Eclipse GS- sold
99 Eclipse GSX- 386awhp
98 Eclipse GS- sold
92 Prelude

www.nopi.com it was like 460 or something after shipping I think.

Non modular CM stage 3 w/ CM aluminum flywheel

I think Modern Performance has them for like 430.00 or something like that.

Thanks for letting me know Patrick...

i can't wait until i start breaking drivetrain parts - i'll be able to learn a lot more about the NVT350 and i'll be able to upgrade to a LSD. the increaced traction must be really good. my transmission has about 136k miles on it, but it still shifts very smooth and doesn't grind at all. i justify having things break is good, because you replace it with something better than stock. it's expensive, but hey... in the end you end up with a really nice car.

2016 WRX STi Limited (current)
2001 A4 1.8tqms (donated)
1991 GVR4 #1933 (sold)
old.dsmregistry.com/detail.php?carid=218 (dismantled)

you get the clutch and the flywheel for 460??? damn..thats a good price..i will have to look into that next time i replace mine..non modular is much easier when it breaks b/c its not 800 to replace the pressure plate...good deal...so did i read that right, 460 for the both combined??

400whp or bust.

No, 460 for the clutch kit only (pressure plate, clutch disk, TO bearing)

and 420 for the aluminum flywheel, for a total of ~880.00 for both.

You can just get a '95 neon flywheel at a junk yard for around 50.00 and then have it resurfaced for ~20.00. That would make it still cheaper than a modular clutch.

I just bought the aluminum flywheel because I like to wast money (as you can see)

Breaking drive line stuff isnt fun in any way, shape or form. It sucks ass. I would much rather do anything else to my car than work on that part. (too many bearings)

wow, so how much horse power are you pushing? have you gotten on a dyno?

New Car:
2004 350z base, Nismo CAI, pioneer avic-n1 (dvd, cd, navi)



Old Car:
1998 GS with hrc stage 2, HID 6000k conversion kit, AEM UEGO wideband, sfmu, ml, prokits, Greddy warning gauges: egt, boost gauge, and oil pressure, apexi tt, haydans tranny cooler, costum dp, groundwires, dynotune fp gauge. gst muff, turbo spoiler
Boostin since Aug 03.

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!

why didn't you get stage 2 axles? I sent you a PM

Brian, I'm glad your ride's back on the roa Did you install the Quaife yourself or did a shop install it for you. The reason I'm asking is, I read in the current issue of Sports Compact Mag and they said something about you needing to align certain things, it's not easy, etc. How did it go?

___________
Kon C

"Sometimes, a man has to do what a man has to do."

Muahahahaha... If you like wasting money, then go ahead and pony up another 700 bux for the last set of axles that you will ever need to buy (Driveshaft Shop stage 2).
-=B-=

>Muahahahaha... If you like wasting money, then go ahead and
>pony up another 700 bux for the last set of axles that you
>will ever need to buy (Driveshaft Shop stage 2).
>-=B-=

but i believe that 992gnt broke one of his. but i could be wrong

http://home.bendcable.com/optimuspeterson <<<<HRC Stage 2 and Star Instructions
95 Eclipse - SOLD | 93 BMW 318is - SOLD | 2000 S-10 Extreme on 20's - SOLD
93 Toyota/shaved/bagged/body dropped - SOLD | 97 GSX - SOLD
2006 Scion tC

As far as the axles go I do know about them but have yet to get around to buying them. I will probably get them sometime soon...


Kon,
I had a shop put the bearings on it and I did the rest myself. Nothing to difficult really, I just used RRE quick like semi walk through.

http://www.roadraceengineering.com/quaife.htm

Unless you are already breaking axles, do not bother. Some cars break them, some do not. Armond broke tons of driveshaft shop axles. They have redesigned them after he kept sending them in showing what was breaking which was different most every time. They have held up now and I suspect they will hold up for most anyone else. I am still on stock axles myself.

05 Mazda RX-8
06 Lotus Elise

heh, snapping axles... i cant wait till the day i snap an axle, its gonna be awesome!

Boca Raton, Florida
95 Eclipse GS- sold
99 Eclipse GSX- 386awhp
98 Eclipse GS- sold
92 Prelude

I broke a Stage 3 axle, thank you very much! They don't even make the Stage 3's anymore, but they're really nice.

Greg

'19 Genesis G70 3.3t AWD
'88 Chrysler Conquest TSI

It’s not really that big of a deal when they break because of the life time warranty on them. As for my car breaking them, it does and this is the third stocker that has broke. This one was the first to completely snap so that the wheel wouldn’t turn. The shop that I get my OEM parts from hates me. Oh well