Hey i see that the harness is short how did you guys do to connect it to the ecu in front of the car, without having to mak ethe cable longer and still gettting the options of taking the safc out at nights ? ???
Guys with Safc do you guys take out your SAFC at nigh so no one will steal them, here in FL with have lots of haters so i need to take it off.
when installing the SAFC did you guys sodered on ecu or did you guys tapped into it and put tape on it?
#35756, "RE: Safc install info" In response to Reply # 0
Depending on where you mount the SAFC, you may or may not have to extend the wires. I have mine sitting by the vents in my center console and I didn't need to make the wires longer.
I would definitely recommend soldering the connections. You really don't want a wire to come loose and mess with your fuel settings, especially while boosting!!
You are not your job. You're not how much money you have in the bank. You're not the car you drive. You're not the contents of your wallet. You're not your fu**ing post count.
#35757, "RE: Safc install info" In response to Reply # 1
Use Category 5 ethernet cable to extend your connections, and DO SOLDER! I ran 9 feet of it tucked neatly away behind the ECU, so if i ever want to reposition my AFC, i'm free
Jon
1997 Eclipse RS
14.21@101mph 10/4/02
MODS: 8.8:1 JE Pistons / Eagle rods / Stage 1 Hahn turbocharger / Melling Oil Pump / Autometer 5" tach / 4 JL 12" W0 subwoofers / Clarion 230w amp / short shifter mod / GReddy EVO exhaust / custom 2 1/2" downpipe / no cat con / CM Stage 1 / 30lb Mustang injectors / TurboXS MBC / 1G SMIC / Eibach Sportline springs / KYB GR-2 struts / GReddy 52mm EGT / A'PEXi Super AFC
#35758, "RE: Safc install info" In response to Reply # 2
hey BoostedGS do you have option of taking it out or not.
hey HiOnPSI that is great idea did not think of that. I guess i am gion to go thta route because i do not want to have broken glass for an SAFC.
Now is there different setup for SAFC on our cars on only1 wires can go in only 1place right ???
Also anyone here using the Corbing fool the SAFC. if so how much more better is it that not using it ?? can someone explain to me becuase i really did not understand in his site , too tech hehe lolz
#35759, "RE: Safc install info" In response to Reply # 3
Yes, technically I could. My SAFC is mounted on the bracket it came with and the bracket is pushed into a slit on my center console. I could just pull the bracket out and unclip the wires at the plug that is under the dash.
You are not your job. You're not how much money you have in the bank. You're not the car you drive. You're not the contents of your wallet. You're not your fu**ing post count.
#35760, "RE: Safc install info" In response to Reply # 4
hey boostedgs where do you have it installed the the ecu on front of car???. because man my harness is only 3 feet so it is not even long enough to get it through firewall.
#35761, "RE: Safc install info" In response to Reply # 5
I'm guessing you didn't buy this SAFC new then, because it sounds like you're missing a piece. You should have about 3 feet of wire coming from the SAFC itself with a plug on the end. Then you should have another piece of wire about 6 feet long that has a plug on one end, and open wires on the other end. The open wires are to be tapped into the ECU wires. If you don't have that 6 foot length of wire, you'll definitely have to extend the wires!
You are not your job. You're not how much money you have in the bank. You're not the car you drive. You're not the contents of your wallet. You're not your fu**ing post count.
#35762, "RE: Safc install info" In response to Reply # 6
I have the corbin SAFC boost mod. I could not think of using the AFC in a boosted car without it!!!!!
MUST GET IT! _________________ Vinnie Lima vinnie.lima@jvllogistics.com AIM: Kiku888 1997 Chrysler Sebring "Silver XTC" I4 420a w/ HRC Stage 2.45 w/ FMIC 14.7@97 mph@6psi Proud member of the ASOG BoOsT JuNkIe Crew
_________________ Vinnie Lima vlima@csc.com AIM: Kiku888 1997 Chrysler Sebring "Silver XTC" I4 420a w/ HRC Stage 2.45 w/ FMIC 14.7@97 mph@6psi Proud member of the ASOG BoOsT JuNkIe Crew
#35764, "RE: Safc install info" In response to Reply # 8
I too would like more info on Corbins mod. I understand it uses a sensor to fool the ecu. Instead of advance timing and knock it tunes on boost? Correct me and please explain also the basics. I want a s-AFC but wouldn't do it till I knew 100% this mod. TIA.
weasle745: and then to top it off, im not even an attractive guy. I look like Millhouse from the Simpsons, cant put on weight if my life depended on it, etc
Search
Printer-friendly copy
3 Users in Chat
