Just wondering but I was checking out that TTI stainless steel headgasket and was wondering if there were any other cheaper head gaskets out there that work as well. I'm planning to do a small rebuild sometime in the near future and was just wondering if there are better options. That TTI head gasket lowers compression by on 1 point also, so if I got like 8.6:1 pistons it'd make it a 7.6:1 and that's too low. Will a stock headgasket hold up to a lot of boost?

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

OOPS, nevermind, i thought you meant manifold gaskets. Sorry, it's 1 AM in the morning and tired as hell. Ignore the link below.

I've heard good things about these: http://www.ttiracing.com/neonproducts/sohexhuastgasket.htm#

Kris
"Someday............I'll have traction problems!!!!"
Tampa, FL
Pinoy Turbo 2GNT

1999 HRC Turbo RS
Stage 2
Auto with BOOST!!!!!!!!!!!!

When I do my rebuild Im getting an aftermarket stock compression head gasket. I highly doubt the stock gasket is going to hold the boost I plan on pushing but I dont want to lower compression anymore than 8.6:1

Robert Parkhurst
toykilla@comcast.net

Stock MLS gasket has been run on 30 lbs of boost and survived.




________________________________________________________________________________________
current status - No 3rd Gear synchro


http://hometown.aol.com/ohshootuhh/
www.Fast420A.com

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

MLS what's that stand for? Can I get that at kragen?

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

if i remember correct it stand for... Multi layer steel? i know its alot better then the ones that are on the car since mine has been replaced... much more better

Michael 99gs
Boost It!
Mods:
no time to put in yet:315cc injectors, & crane ignition.
Hrc Stage 2
S-FMU
Greddy Type S Bov
VC-2
Road Race Catch Can
Greddy Profec B & Switch
Apexi WS Catback
Super Afc
Autometer Boost,
Egt,Tranny Temp Gauge & Cooler
Air/Fuel Light & Digital
Tokico Adjust Struts
Eibach Pro Kit Springs
Front & Rear Upper Bar
CarCraft Interior
Sound System= Bring it On

Michael
99gs hrc stage 5000 SOLD...
2004 Honda Accord V6 (240 hp)stock
what other car should i buy?? hmmm
Car info & pictures at http://www.cardomain.com/memberpage/520269

Go to Chrysler. Order the stock MLS (mulit-layer steel) headgasket. Continue rebuild.

05 Mazda RX-8
06 Lotus Elise

Yeah go with the MLS gasket great for the turbo, best all around sealing. And the numbers stated from TTI make me think that their gasket drops C.R. more than 1 C.R.

Una salus victus.
It's not about being invincible, it's about being ready; for anything.



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, Crane Fireball HI-6DI2, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors & Carbon Fiber Pads

To Be Installed: P&P Intake Manifold 1/2, P&P Milled Head, Rear Disc Brakes, Rear KVR Cross Drilled Rotors & Carbon Fiber Kevlar Pads, SS Brake Lines

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

aight cool thanx guys. ne1 know the part number? So I should just roll up to dodge and ask em for a stock 420A MLS head gasket?

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

A very good and economical head gasket is the factory MLS. You could get one from any Mitsubishi dealer for about $80. I believe that it's the same type of head gasket used in the turbo models.

___________
Kon C

"Sometimes, a man has to do what a man has to do."