Hey Guys, I'm about ready to order my HRC stage II. I know that anyone who's mechanicly inclined shouldn't have a problem intalling it, but I'm wondering if I have all the right tools? I know I need a hacksaw to cut the downpipe. Any other special mods that have to be done for the install?
I need to know this because I have to get this installation done as quickly as I can. I was going to take my time and drive my Cherokee around while the car was in the garage. But, my jeep was stolen a couple days ago so now I have no x-tra wheels!
Perf: KYB AGX Struts Neuspeed Sport Springs 5 Strut Bars (2 F/U, F/L, R/U, R/L) Sprint Front Camber Kit $15 Rear Camber Kit MSD DIS-2 Ignition System Some Regrind Cams that need High Compression (which I don't have) Ported Intake Manifold Ported Throttle Body Corbin's A/F Gauge Nameless Cold Air Intake with a K&N Filter Custom 2 1/2 inch exhaust with Dual DTM Muffler Empty Catalytic Convertor Energy Suspension Motor Mount inserts Hurricane_GS Short Shifter Symborsky Shift Kit Clutchmasters Stage 3 Modular 225/50/16inch Wheels and Tires
Audio: Alpine CD Head Unit Alpine Flex4 25W X 4 for Fronts and Rears Alpine V-12 450W X 1 for Subs Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears Blaupunkt 3 way 6x9's in the rears 3 MTX 5000 10" 12 ohm subs running 4 ohms mono
Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...
#11781, "RE: HRC Install?" In response to Reply # 2
Don't worry, I'm a jet engine mechanic. I bleed from those suckers everyday. I LOVE IT!
We don't have to drill a hole in the oil pan do we? Also, since I've heard that the HRC FPR sucks, should I just try to convince HRC to not send me theirs, and just buy a different one to begin with? Or, are their FPR's no worse than any others out there?
#11782, "RE: HRC Install?" In response to Reply # 3
Some people have problems with the HRC fpr idle pressure fluxuating, but I havent had any problems. If you can get a credit from HRC on that fpr, I would do that and get the vortech s-fmu with the proper calibration disk. The general consensis is that it is significantly more reliable and more tune-friendly.
You will have to drill a hole in the oil pan and install a fitting for the return line from the turbo. It isn't very difficult to do, just make sure that you do it in the proper location. Someone not too long ago posted a picture of exactly where to mount the fitting... I dont know if you run a search if you will be able to find it or not. I just used the HRC instructions and didn't have any problems.
Good luck and welcome to turbo world Oh ya, and where do you live at b.t.w.? Matt HRC Stage 2
Matt 1995 Eclipse GS 2.0L, S16g Turbo, 8 Injectors, 26psi
1998 Eclipse GSX 2.3L Stroker, AEM EMS Converted to Speed Density, FP3065 Turbo, 35psi , and so on...
#11784, "RE: HRC Install?" In response to Reply # 5
Also the oil return line hose that hrc includes in their kit is way too short to properly install it in place. Go to pep boys or an autostore and get at least 2 feet of insulated and reinforced heater hose instead.
Also go to homedepot and buy a bit for your power drill that cuts the hole on the oil pan for the right size.
you'll need all kind of sizes of metric wrenches and sockets....get a 22mm wrench to remove the o2 sensor from your downpipe for when you saw it as well.
_________________ Vinnie Lima vlima@csc.com AIM: Kiku888 1997 Chrysler Sebring "Silver XTC" I4 420a w/ HRC Stage 2.45 w/ FMIC 14.7@97 mph@6psi Proud member of the ASOG BoOsT JuNkIe Crew
#11787, "RE: HRC Install?" In response to Reply # 8
btw, while you're still in the "force" get your airframe and power plat license with you gi bill cause they will cost you the price of a stage 2 when you get out. i work for delta and the mechanics here make 22 an hour starting off.
#11788, "RE: HRC Install?" In response to Reply # 9
Well, it's not what you think. I'm a engine mechanic, crewchiefs work on the rest of the plane. I'm not active duty either. I am in the Oregon Air guard, but I work for them full-time as a technician. I make way more bucks than active duty people (been in a year and a half and make $20.13 an hour). This makes a lot of active duty people mad because they never knew about that side of the guard when they enlisted. We don't have an auto center on my base so I'm just going to have to clear out the garage.
I was thinking about an A & P license, but now with all the layoffs there is no demand for those mechanics. I'll stick with the guard and retire in 30 years.
Thanks for the tips, One more thing, how hard are those old Starion intercoolers to install?
#11789, "RE: HRC Install?" In response to Reply # 10
hmmm....that's odd i never heard of a backshop mechanic getting paid hourly. might have to do some research on that. and as for the lay-offs. hahaha. sure all the other airlines are going down but Delta's already starting to make a come back. in the past when other airlines went down Delta has always recovered. but they should be hireing back up in another year. VERY little people have been layed-off from Delta after sept. 11th. but it's all in what you wanna do. just lettin ya know some of ya options partna. but the starion intercooler.....hmmm....i've been thinking about getting one for my GSX. hell if you can't get it to bolt on....talk it to your local muffler shop and have 'em throw a couple spot weld on it. but as far as bumper clearance you shouldn't have any problems. i also think the 420a guys have to modify the tubes to go the opposite direction due to the throttle body being opposite side of the 4g63 which the starion intercooler was designed for. but hadesomega would know more about that. he's got some pics and everything of the whole process.
#11790, "RE: HRC Install?" In response to Reply # 11
Couldn't you just turn the intercooler around so the tubes face the opposite direction?
In the guard we get paid by the State Government. Not by rank, but by what your job is and how long you been working there. Crew chiefs in the gaurd are two pay grades higher than I am. They start out almost $20 an hour, and just goes up from there.
#11791, "RE: HRC Install?" In response to Reply # 12
I was wondering the same thing about the intercoolers. I noticed that turbo fmic inlets and outlets face the left while ours need to face the right, couldnt you just flip those intercoolers over?
Search
Printer-friendly copy
0 Users in Chat
