I finally got all of the fuel system components installed for my 8-injector setup. Its running good and leak free. I've had some time lately so this week I decided to go ahead and finish this thing up. First I'd like to thank Corbin for pioneering the 8-injector setup on our manifolds. Second I'd like to point out that the "size" of this system was inspired by an article by Steve Wells - http://www.stevetek.com/R-FuelSys.html -6AN all the way through, and -8AN to tie the rails together. I will eventually get the turbo on but I decided to use an 8-injector fuel system and I wanted to install the fuel system first because it was so involved.

I'm using an Aeromotive 1000-6 regulator and a high flow Russell fuel filter. I fabricated a SS bracket to mount them on the passenger side.


To get the fuel back and forth to the tank, I used -6AN aluminum lines. The line fittings are compression-fit AN adapters. You can see they go from the filter and fpr through the slot between the frame and suspention brackets - all the way to the back - right before the tank.



The tank outlet has a -6AN thread fitting on it. It's actually not a JIC fitting, but it has the same thread size as -6AN. So I used some teflon tape and tightened it down good. It works. The return is a different story. It's a puny little line and that just wouln't do. So I modified the tank lid by installing a -6AN 90deg bulkhead fitting. It turns out that the best place to install it is right underneath where the outlet line is - so i had to bend the outlet line out of the way for clearance. Seems to do the trick -6AN in and out. I left the old return inlet on there and just capped it off.




I know I've posted a bit about my manifold before, but I've changed ISPs and that thread doesn't bring up the pics anymore so I'll put a couple of pics here. I bought a spare manifold and did all of the fabrication myself - Drilled the injector bosses, made a bracket for the secondary rail, and welded -6AN and -8AN fittings to a couple of 95' fuel rails. The -6AN ports go on the fpr/filter side and the -8AN ports are used to tie the two rails together in seris.







Here's a shot of the -6AN lines on the passenger side and one of the -8AN rail tie on the drivers side.



I've got a fuel pressure gauge mounted directly on the fpr and I have an electric gauge installed in my gauge bezel. The pressure sender unit is installed right after the secondary rail(or right before the fpr). It's the gold thing in this picture.



Of course when I first started testing it I had a couple of leaks here and there. I had to epoxy the primary rail a couple of times. A couple of the compression fittings needed tightening. While I was wating for the epoxy on the rail to dry I decided to install a couple of switches. I had already rewired the pump when I installed it and my relay is behind the interior panel next to the pump....so thats where I installed the switches. Right behind the passenger's seat. I can reach them from the drivers seat. I like the location cause they're out of the way. The green one is the main Power switch - it enables/disables the pump. I wanted this for parking at bars, concerts, and whatnot. Cant steal the car without fuel pressure. The blue one is a Test switch - it turns on the pump. Even with no key in the ignition. Great for leak testing, changing fuel pressure, etc.


Other than that, the EIC is installed and running. I'm using the same 034 EFI unit that Corbin has in his writeup. It doesn't really do anything right now because I don't have a turbo yet. But at least it's installed. Right next to the ECU - in the same bracket.


I've got 30 lb'rs in the secondary rail. That brings the total flow to 550cc which should be good for ~350-400hp. Amazingly enough these secondary injectors are the bottleneck on the system right now. Not that I'm getting 400hp N/A...but
1)the lines, fpr, and filter are big enough to flow ~1000hp.
2)the 255lph high pressure in-tank pump can flow enough to support 48 lb'rs in the secondary rail, which would bring the total flow up to 740 cc/min - good for ~500-550hp
Then the question comes up - Isn't this a little overkill Jim? Well, I wanted to build it so that I didn't have to worry about running the secondary rail dry. Think about it - the injectors are sucking from the top of the upsidedown rail - where the air is. Read that SteveTech link I mentioned ^^^ for more info on how inadequite our delivery system is. I guess the other thing is that I want to have a seriously big turbo at some point. Like, I've been thinking 20g for a while, but lately I've been thinking FP3065. Who knows what I'll be thinking when I actually get it. I'll settle for starting out with this 14b that I have for now.

Anyways. Like I said its running good. I had the pressure set a little low at first - 45 psig static pressure. The LTFT was hanging around 20-22 on my test drive so I raised the static pressure to 52 psig. Now the LTFT stays under 15. One other thing I noticed was that my idle is extremely stable now. Before it would vary from 700-800rpm when flipping between rich/lean cycles. Now it sits at 800rpm steady - no fluctuation at all. I'm happy with it. Now I can move on to the turbo.


95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html


95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

U da man !


^^Pretty much sums up my dsm life^^


Member # 333

Congrats dude!

95 GST | So-Cal

EXCELLENT


HAHAHA....great work MJ!

getty up

-kent-




'98 Talon...gone, but not forgotten

I'm getting nothing but red x's man!

96 Indy Red Dodge Avenger I4 5spd
225.7whp/227.2wtq @ 10psi, currently running 12-14psi.
HRC Stage III turbo setup
JE 8.8:1 pistons
Eagle rods
block bored .020" over
GReddy FMIC w/ custom piping
1G crushed BOV
SPEC Stage 3 clutch
2.5" DP, 2.5" high flow cat, 3" ERT catback w/ Magnaflow muffler and 3" tip.
much much more...

really nice man.. how much has this project costed ya?

~STV~

Great job man! I'm in the same boat now too, starting to design my 8 inj setup. I'm going at it a bit different, with a more "user friendly" placement of the new rail and second set of injectors. Should be fun. Now get that turbo on!

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Greta job, Jim!

Ya gotta love the 8-injector setup. It runs reliably, strong, and you get great gas mileage too! I know you'll be pleased once you get all the tuning down.

Wondeful clean work, man.

_____________________________________
Jason ESi-T

04' BMW 325Ci
91' Nissan 240SX
98' Eagle Talon ESi (sold)

Good work Jim...I see you're not afraid to venture out and find your own solution to a problem.

Corbin

'95 ESI-T
HRC+FMIC+ETC...



Gimme fuel...Gimme fire...Gimme that which I desire

That looks like a solid fuel setup. I've had the Stevetek fuel system on my "to do" list for a while, and having seen how nice yours turn out, I might have to gather the parts soo

___________
Kon C

"Sometimes, a man has to do what a man has to do."

that looks sweet.
Michael
99gs HRC Stage 2000 8-Injector Setup
2004 Honda Accord V6 (240 hp)

why are those same pictures on gottude

mototool used the exact same ones in a diff thread
_________
96 talon esi-t
san clemente, ca

as needles of ice
are the ill winds' talons
the coldest of shadows
they seep unto the bone

nice!!!!

corbin.. wanna design sum fuel system for the SRT????

clean work jim!

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

Hey guys...I no I sound like a n00b, well I guess I am.
I have herd much about this 8 injector setup. Im just wondering why people do it...I have read and not sure, but I think its one of these 2 reasons.
Is it for one your daily driving you want to keep a low injection of fuel, and when you want to race you switch over to the higher injection.
Or do you combine injection to make one huge amount of fuel going in…but then why don’t you just put in 650’s and save your self all the trouble?

As you can see im confused, please don’t bash me…lol im stupid.. so what

Thanks guys.

Well the installed system cost a bit - just over $1100. Here's a link to the part breakdown and prices http://www.dimensia.com:81/jimbo/netfiles/FuelSystem.htm It was a little over $500 for all of the fuel delivery parts like lines, hoses, fittings, fpr, and filter. Then it was $600 more for the other components like pump, spare rails, spare manifold, EIC, injectors, etc. I did all the fabrication and installation so it only cost me in parts. I definately spent more that $1100 when putting it together. Some of those fittings are expensive and I've changed my plan several times along the way. Which reminds me, that link to the FuelSystem part no's and prices is the final list. I know I've shared that with several people on AIM before, and it changed here and there along the way. Some of the big changes from what I've already given out were that I got rid of the drain, changed the rail tie to use hose, and changed the return fitting to be the -6AN bulkhead. But that link shows the final list.

As far as how that picture got on Gottude - I IM'd some of these pictures to Bill along the way. I've been slowly installing parts for this system now since July. I show my AIM buddies what I'm doing when I'm online - which hasn't been often lately(sorry). But I didn't think it was a good to start threads about it here till I was done. Like I said, quite a few things have changed from the original design.


95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

Lookin good! Your going to love the control you will have over a rising rate fpr.

____________________________________________________
four nails four corners four riders and four horses

those pics are metal jims 110%

we talk on aim i uploaded them fora thread of somethign way back when. dont remember exactly why.

Looking Awesome Jim!

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

Jim, we're going to have to some serious talks about this when we pull my engine man. I'd like to understand this all in a bit more detail. I'm thinking about pullin' come March - what's your schedule look like? Give me a call or drop me a line.

Great job - looks awesome, can't wait to see it

1999 Eclipse GST 4G63

very nice Jim, much nicer than mine, lol

95 Avenger
ATX->MTX Swap
Holset HX40 @ 26 psi

I copyed jims system some different things mostly the same just not as complete i just used rubber fuel line to connect the 3/8 return line back to the tank i dunno maybe 6inchs of it kinda tachy but no one will see it. Great idea and very clean. Keep up the good work.

Hey guys...I no I sound like a n00b, well I guess I am.
I have herd much about this 8 injector setup. Im just wondering why people do it...I have read and not sure, but I think its one of these 2 reasons.
Is it for one your daily driving you want to keep a low injection of fuel, and when you want to race you switch over to the higher injection.
Or do you combine injection to make one huge amount of fuel going in…but then why don’t you just put in 650’s and save your self all the trouble?

As you can see im confused, please don’t bash me...

NOOBIE GET THE FUCK OUTTA HERE!!!!!

J/K

Here's my understanding... Hopefully its right...
8 injector set up.. It mimic the stock fuel idle or when not in boost (smaller primary injectors fire–where the stock injectors would be); while getting enough fuel when your running a lot of boost/power (the secondary, mounted by drilling through the intake manifold, I THINK). The secondaries fire as boost increase.

Since we can't use 660cc injector for our primary stockers, we can use the 8 injector setup to have enough fuel, while idling like stock.

Hope I helped...


-------jezreel
hrc stage 1, sfmu, ml, prokits, egt, boost gauge, apexi tt, haydans tranny cooler, costum dp, dynotune fp gauge. gst muff, turbo spoiler

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

Very nice Jim! Once again your knowledge showing, looks very good, congrats.



Exile Racing Technologies: http://www.exileracing.com
una salus victus
It's holding down the garage floor right now.

nice job man
but
did you drill the holes with a countersink

1998 dodge avenger 4 cyl AT
Mods are:
Not enough

Good eye. Yeah. I explained why a bit better in a thread I posted about finishing the manifold - http://forums.2gnt.com/dcboard.php?az=show_topic&forum=8&topic_id=49086

...but like I said, I've changed ISPs and the pictures unfortunately don't show up on that thread anymore. Basically, I used the countersink because I don't have a drill press big enough and I didn't want to get one that was big enought. ok ok, I wanted to get one but my wife would have killed me if I got the one I wanted. I'll post the missing pictures and a brief description here so you might have a better idea about what I was sayin in that old thread.

Here's a side shot. I spent a while setting it up so the angle would be just right.


I'm lining up to drill a runner right here. Notice the marks on the board, and the "dowel" bits I referred to in the other thread.


This one shows the top platform off so I could drill the pilot hole. Notice that I already started the cut with the countersink bit while the rig was assembled. It would go far enough in so that I knew where the hole would be centered, but it just wouldn't go in all the way without drilling a pilot hole.


This one is a closeup of the pilot hole that I had to drill.


The countersink would go all the way through after getting the pilot drilled.


Get all the bosses in there and stick the rail on it....


...and glue em in.



95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

Jim you'd be better off w/ a 20g buddy. A fp3065 is such a serious overkill its not funny. We will be building a 1st gen awd here soon w/ this turbo and you wouldn't believe how big it is. You'd need 550's in the secondaries to keep this thing happy. We have a guy on my board with a 3055 maxing out 660's at 19-20psi. That turbo has a 4" inlet! Its just sick. Probs on the setup. I used alot of expensive parts w/ my 8 inj setup as well, i just need to do the braided lines and i'll be quite satisfied. It looks pretty clean!

400whp or bust.

the 3065 is so nice though...

kinda over priced for the performance you get back but who cares atleast you can say yea i gotta fp 3065

You can have it cheap, fast or good. Pick any two.

If you want it cheap and fast, it's not going to be good.
If you want it cheap and good, it's not going to be fast.
If you want it good and fast, it's not going to be cheap.

Mototool - The other white meat!

"He might just be more badass than Dino." -DR1665

Yeah, I was told to use teflon paste on fuel lines, rather than tape. Although I wouldn't think tape would leak any more than paste...


1996 Eclipse RS / 5-Speed / Aerogear Body / Coated in Magnetic Red Metallic rev.2 / T3 Turbo Intercooled @ 8 psi / More at http://home.insightbb.com/~mgalyan/
Mark Galyan - Indianapolis, Indiana

Its not really an AN fitting. The hose end is a 6AN, but the thread on the tank cap is a straignt thread hose fitting with the same thread as 6AN, 9/16-18. Generally you don't have to use tape on JIC connections, but I did because the male end isn't a JIC - its something else. I wrapped the teflon on nice and thick, tightened it up snug. 800 miles so far and it hasn't leaked.


95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

off topic: there's a LOT of good information in here. this thread gets my official nomination for "things we've seen before"

2016 WRX STi Limited (current)
2001 A4 1.8tqms (donated)
1991 GVR4 #1933 (sold)
old.dsmregistry.com/detail.php?carid=218 (dismantled)