i got a front urethane body kit that was cut into a few parts. what can i use to re bond urethane? it has to be strong and hold it together. ive used fiberglass before but it isnt flexible and id rather not use that. ive seen plastic looking welding sticks. do they work? what about urethane that is used to mold kits on to cars and stuff?

91 civic hatch, homemade turbo+ LS motor = 12 sec street car.

rivets and fusor 142 .

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

what is fusor ? andto rivet it i would have to over lap the parts. i need them to meet together not over lap.

91 civic hatch, homemade turbo+ LS motor = 12 sec street car.

ever try duraglass? I would give that a try! I have never used it on urethane, but would think it would hold up pretty good!

--------------------


- 05 Subaru STi
- 97 eclipse gs (289whp w/ 276tq)

it dont overlap .fusor is used in every shop that does plastic repair . not many shops do plastic repair tho since the part is usually cheaper than the repair . you also have to plastic weld when using fusor . firstget some little strips of sheet metal .drill 2 holes in them . line up the 2 pieces that need to be put together . drill 2holes in part ,1 on each side . put the rivet through the part then through the sheet metal . this when the parts dont overlap . tape the front . weld the back . take tape off front . grind the rivets down and apply your fusor to fill the rest . sand and your done . also for small holes in urethane you dont have to plastic weld or use rivets . you just tape the front of the hole , lay down fusor then put a layer of fiberglass cloth and roll it into the fusor . then fuse the front and your done . hope this helps .

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

i tried to plastic weld . it didnt work so well,.

91 civic hatch, homemade turbo+ LS motor = 12 sec street car.

I used the 3M uretahne glue. The ones that hold your windows in place. Strong sticky stuff, this was for the under side of my rear bmper through the inside.

The outside is unoticeable un less your 1 inch away. You can see the paint crack. Im in no hurry to fix that.

Member # 751


FOUNDER of the Central Cali chapter of 2GNT!
(I got kicked out after I refused to go Cow tiping) - Hehehe you know who this is for

whatever i use has to handle stress cause its cut right where the bemper mounts to the car .

91 civic hatch, homemade turbo+ LS motor = 12 sec street car.

when you plastic welded what rod and shoe did you use

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels