Well I am still working on my gauges but I love how the rest turned out so far. Thanks to HondaHater and iamnotwhoiam....

Tell me what you think!!








Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

Looking good. One of these days I'll get around to doing that.

Jason
'11 Ford Mustang GT/CS
'11 Ford Mustang V6 6-Speed (SOLD)
'04 Nissan 350z Touring (SOLD)
'95 Turbo Eclipse GS (SOLD and will be missed)
'90 Talon TSi AWD (SOLD)

Damn those look cool as hell

built turbo 99 rs-back to stock and parted out
Now: 2003 S2000 Aem ems, 1000cc injectors, inline pro 3mm headgasket, T67 turbo, full race manifold, Tial 44m wastegate, Tial 50mm bov, 255 fuel pump, kaaz 1.5 lsd, comptech bearing caps, j's 4.77 gears, and so much more

i did my main hvac controls.. but how did u do the ac button, and the other buttons??? same way?

~Lisa~

www.liquidimaginationz.com
www.extremecarsinc.com

:thumbsup

I like how it matches your radio

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

ac button's a bit harder. you gotta wire the LED to the circuit board inside the switch. not a lotta space in there.. plus you gotta put the resistor in there too. oh and that's only for changing the snowflake. i know some people wanted to do the green/orange light. that's an even bigger bitch.

-marc

='95 RS 5spd Red=
CAI
A'pexi N1
Hanabi 8000k HID
SPAL Deluxe Power Windows
Nakayama GT5 17's
GSX Calipers
AEM Rotors

255 is fricken short

good work...

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

it looks like my car that kicks ass everytime i see it

The 2GNT is Gone... and the curse too!!

Actually the way I did it was to make a wiring harness that all of the buttons connect to. So basicly from that main plug of the HVAC light it branches out into like 8 different 2 wire connections. I did not have to solder anything directly to the switches. It will be really easy to get it back to stock as well if needed because all I have to do is pull the LED out and put the old light back in since none of it is soldered to the boards. For the AC button I just mounted the light and ran the wires straight back on the flat spot of the switch. Then I took the dramel out and got ride of the lip that comes down in the mounting hole on the top. Fits really snug still and works well. Its strange because I didn't do anything for the other AC light but it lights up blue when off and green when on. Worked out really well....

I love how it looks with my stereo aswell and actually that was th main motivation for me to get it done. Should look really good once I get the sAFC hooked up and the gauges done.

Thanks for the props guys!!

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

did you use varad led's or reg led's cause those are pretty bright and how many did you use

i wanna do my defroster buttons and all thoose...put i painted over them siulver to match my interior. And if i take the paint off..the button will not match. But i am torn because i love how urs looks. I got my hvac blue...but i want those buttons to now. damn u

----------------------------------------------------------------------------
home.comcast.net/~nappyjim/songs.html
home.comcast.net/~7291834avi/carputer/carputer.html
www.cardomain.com/id/napppyjim

*Proud Member of the Top Ten Post Whore Club*
*Proud And Co-Founding Member Of The Zoom Zoom Revolution*
nappyjim-3 Chip-0
No one likes you chip, go away.

hehe .... sorry Jim

I used LEDs I found at a local electronics supply store. They were rated at 2500-3500 MCD depending on voltage. I used a lower ohm resistor to up the voltage to the maximum the LEDs were rated at. I think it was like 4.5V and I used 1/2 watt 270 OHM resistors to get it pretty close to that.

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

oz gs, you got time to write something up closer to plain english? i wanna do that so bad cuz the colors would go with my panasonic head unit beautifully but i aint understand a word you said. ill grab your aim name and try to catch you on there

that boy K-Y
kbnkb@sbcglobal.net
talonky36 (aim)

04 srt-4 (low and slo)
96 talon esi (still broke make me an offer)

I will try and get some pics of what I did later on this week.

Chad

MODS:
3" PVC CAI, GST Muffler, Greddy 4-1 Header, AFX UDP, 55 mm bored TB, P&P Intake Manifold, Corbin intake spacer, gutted cat, Apexi S-AFC, KYB AGX Struts, Eibach Prokits, Excel TZ-10 Rims

yeah if you could write something up i'd love it .. i tried doing something like this over on my cruise control / foglight buttons and now the lights dont work .. if you could write something up it'd be most appreciated

____________________________________

Another BANNED asshole.

Sweet Dude. Can you email me some direction at scothern@insight.rr.com? I have already done the HVAC and want to do the defogger and the AC buttons. I'm just not sure what would go where. Can you help?

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=



99 Eclipse RS

"Can't we all just hit a Bong"?