Is this hard? How would I do this


Thanks a lot

Jeff

For Sale: 98 3Piece Spoiler email me
www.wrestlewarehouse.com

http://www.auburn.edu/~fauchpj/headlight.htm

So is that the only way to do it, to heat it to pry it off?

Thanks again


Jeff

For Sale: 98 3Piece Spoiler email me
www.wrestlewarehouse.com

ya im pretty sure

you can do what i did.. take the headlights out.. and break the orange piece from the inside with a screw driver and pliers... i did this a long time ago.. its pretty easy and you dont have to take apart the whole housing... at least, thats was what i was thinking, when i first did it... but i have also taken apart a couple headlamps now, and its getting easier and easier to do... if i would have done it over again, i would probably taken apart the housing.. its a bitch getting ALL the parts of the orange out and not losing the clear piece. if you wanna try doing it my way.. and need a better guide.. let me know... but taking apart the housing isnt very hard.

^^what once was^^


^^what is now.. and permanently^^

yup the 1st headlight will take a little while if you've never done it, the 2nd one will take half as long. but its not hard. just make sure not to leave it in the oven too long.

dsm/mitsubishi service manuals https://www.mediafire.com/folder/5k14qlaulb9s1/dsm_mitsubishi

service manuals(my whole collection) https://www.mediafire.com/folder/ac51jwwa3g1n1/automotive_manuals

Can you do the same with altezza tails? It would be cool to paint the altezza's to match my car. If so, has anyone got pictures?

Allan
2008 Magnetic Black 350z NISMO /1976 Austin Mini 1098 Special (export)

Member# 1980

this is what a altezza looks like

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

yeah d00d you can do it to all cars, haha the guys at my old 3.8mustang board used razor blades to open up the headlights then used silicon (and whatnot) to seal it back up, it looked like a major bitch and several people fucked up and had to buy new headlights, if they only knew there was an easier way i've done it too, its not nearly as hard as it sounds, and its not risky at all (the oven technique)

here read this, its crazy
http://www.fnsweet.com/garage/clears.shtml

______________________________________

11.65 @ 115

Thanks guys, what kind of glue do I use to put the light back together. Whats is called?
Thanks

Jeff

For Sale: 98 3Piece Spoiler email me
www.wrestlewarehouse.com

i just used a tube of clear waterproof kitchen and bath silicon that i picked up from homedepot for like 2 bucks. worked perfect.

sory if i confused you, but just put it back in the oven and the factory glue should reseal itself

______________________________________

11.65 @ 115

>put it back in the oven and the factory glue should reseal itself

yes! its hella easier than having to re-glue it. btw don't be afraid to use the oven. as long as u keep a close eye on ur headlights you'll be okay.

95 GST | So-Cal

**THIS POST IS DOT APPROVED**



Jon

1997 Eclipse RS

14.21@101mph 10/4/02

MODS: 8.8:1 JE Pistons / Eagle rods / Stage 1 Hahn turbocharger / Melling Oil Pump / Autometer 5" tach / 4 JL 12" W0 subwoofers / Clarion 230w amp / short shifter mod / GReddy EVO exhaust / custom 2 1/2" downpipe / no cat con / CM Stage 1 / 30lb Mustang injectors / TurboXS MBC / 1G SMIC / Eibach Sportline springs / KYB GR-2 struts / GReddy 52mm EGT / A'PEXi Super AFC

Jon

1997 Eclipse RS | 2001 Lexus IS300
12.671 @ 111.660 1.586 60' 5/28/04

www.haiokuracing.com