I just bought some hood pins and want to practice putting them on my OEM hood before I go with a carbon fiber hood. I was looking in my engine bay and can't seem to find an ideal place for the hood pins, any suggestions.

98 Eclipse GS:
Greddy Evo
RH z5000 19's
Blitz Kit
AEM CAI

I just put mine in, there Is only one good place to put them that has a lot of room to work with. It the two little black ruber stopers right befor you get to the radiator. just spin them out and you have 2 even holes. If youwant anywhere else it will be a bitch and have no space unless the bolst are really short.

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

Ok, that is the place I was looking at, did you have to cut down your pins at all? reason I am asking is because the holes are only about 1 1/2 inches right above the radiator.

98 Eclipse GS:
Greddy Evo
RH z5000 19's
Blitz Kit
AEM CAI

nope, ithink my pins where 4 to 5 inches. If you want them to be strait, you will have to bend them anyway so they will fit with a hammer

"Only Pirates Say R"
hondahater21@hotmail.com
www.geocities.com/hondahater21

Change Your own Blinker Fluid! --> http://geocities.com/changeyourblinkerfluid/

you can also install them above the head lights. The only thing is you have to drop your bumper and remove your lights. Once they are installed you cut the pins ends with a sawzaw to make them flush and then reinstall everything... maybe an hour tops to everything. I think they look better over the head lights than in the middle.... but you can do what ever you want.....

2006 WW IX MR
2003 BBY EVO VIII (sold)
256.9WHP & 277.9torque
http://s90395832.onlinehome.us/forum//index.php?sid=a70942a7f65043e6c873e12dcd300692

1998 Eclipse RS --show car--

i had to cut my pins down

http://home.bendcable.com/optimuspeterson <<<<HRC Stage 2 and Star Instructions
95 Eclipse - SOLD | 93 BMW 318is - SOLD | 2000 S-10 Extreme on 20's - SOLD
93 Toyota/shaved/bagged/body dropped - SOLD | 97 GSX - SOLD
2006 Scion tC

icedout, what do you mean by dropping your bumper, I think I would like to put my pins over my headlights.

98 Eclipse GS:
Greddy Evo
RH z5000 19's
Blitz Kit
AEM CAI

umm, ya.. i think the spot for em has been said. if u want sum good pix, hit up www.dsmtalk.com and search for hoodpins. thereis a writeup on there that has pix and is very helpful...

for just a writeup and no pix, go to http://seangordon1.tripod.com/how.html

tia

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

best place for hood pins....the hood

Would they look out of place on the trunk?

98 Eclipse GS:
Greddy Evo
RH z5000 19's
Blitz Kit
AEM CAI

I think what icedout means is taking off the front bumper and removing the lights and installing the pins above the lights.. i'v seen them installed there and they look much better than in the middle...

Well if I have to take-off my front bumper that gives me a reason to install my blitz front bumper now , thanks for the info all.

98 Eclipse GS:
Greddy Evo
RH z5000 19's
Blitz Kit
AEM CAI

yeah you need to remove the front bumper cover and then remove both head lights. Install the pins above the head lights. once you have the hood all drilled out and fitted correctly. Tighten the pins in place and make sure it fits properly. Once you have done that, take a sawzaw and cut the bottom of the bolts flush. After all that is done reinstall lights and then reinstall you from bumper. make sure you install all the screws back.. after that your shit will look tight.........

2006 WW IX MR
2003 BBY EVO VIII (sold)
256.9WHP & 277.9torque
http://s90395832.onlinehome.us/forum//index.php?sid=a70942a7f65043e6c873e12dcd300692

1998 Eclipse RS --show car--

I would think more towards the outer edge would be ab etter place for them. Especially with the light hood and worrying about the moving alot in the wind.

Una salus victus.
It's not about being invincible, it's about being ready; for anything.



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, Crane Fireball HI-6DI2, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors & Carbon Fiber Pads

To Be Installed: P&P Intake Manifold 1/2, P&P Milled Head, Rear Disc Brakes, Rear KVR Cross Drilled Rotors & Carbon Fiber Kevlar Pads, SS Brake Lines

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.