so now that i have some money to play with, ive decided to build a 2.3 stroker. heres the basics

2.3 stroker
borg warner s366
je pistons
oliver rods
brian crower 280 cams
ferrea double valve springs and Retainers
mitsu hg
king bearings
arp main studs/connecting rods/head studs
shep stage 4/dog box - still deciding
ptt twin disc clutch
1600cc fuel injector clinic
aeromotive a1000 pump
megasquirt and spark


still deciding on what pistons to use, other then that, this is my setup. any thoughts/changes?

I must question your setup.

-Why JE pistons? Ross and Wiseco have better reviews.
-Ferrea Duals? Kiggly has a beehive valve with less mass and just as much pressure.
-I'd rather go with a Cometic, since their specialty for DSMs is the 2.3 gasket. OEM MLS will do, but I have heard more and more failing.
-If you want the head not to raise, torque them to 100ft/lbs or look into A1 studs, which might be backordered.

The setup will make a ton of power. It will be an impressive machine. However, I would have gone the 2.0 route and rev'd to the moon, since that's where all the power will be.

For your cams, take a look in the marketplace. I might have something for you.

ARP specs are fine, they have many proven years. Remember you have an ALUMINUM head, there's not need to torque the studs down ANY more than 5ft lbs over spec. When doing so you risk damaging the heads surface. When ARP recommends a torque spec it is usually good to stick with that.

Matt
MFG Racing

http://dsmregistry.com/detail.php?carid=1310

i just ordered my je 40 over stroker pistons. next will be the oliver rods and king bearings. after that the t4 s366. what do you reccomend for a manifold?

Call up DNP I am sure they can help you out...

Matt
MFG Racing

http://dsmregistry.com/detail.php?carid=1310

DO NOT get a dnp manifold.

Get in touch with either shearer performance or punishment racing. Lifetime warranties on their manifolds against cracks and you don't have to go through a vendor to get it. I GUARANTEE you'll be much happier going that route.

95 Eclipse RS - Sold and In Montana Now
Project 95 GSX - In Full swing.

decided to go with a t67 instead. still 800hp

have you looked into the sce ics titan copper head gaskets yet? they're nice. You also might want to look into oringing the head and/or deck to make sure you keep seal under 40 psi boost. how many pounds/min does the turbo you decided to go with flow?

95 Eclipse RS - Sold and In Montana Now
Project 95 GSX - In Full swing.

i was thinking still using mitsu headgasket. flows 80lbs a minute....will see around 40psi. a friend locally (roo on tuners) dynod around 560hp and has had problems with his titan gasket.

I Know this, However a guy in our team has had 30+ years of experience with cyl heads/ engines. Him, also me, have seen MANY times a ALUMINUM head being damaged do to being over torqued. We have built many engines. we also have many project cars with 14b's to 42R's 10psi to 50psi. I am giving this as advice and experience for you to take however you will.....

Matt
MFG Racing

http://dsmregistry.com/detail.php?carid=1310

so what do you think of the stock gasket holding 40psi?

In our experiences we have used the stock fel-pro head gasket you can buy at places as cheap as autozone. The gasket combined with a "o-ringed" head has held ballpark 45psi or so on a larger frame turbocharger. We personally use filled o-rings on some of our engines.
I have a Cometic HP head gasket on one of my own cars, & it see's 35+ psi. If you want to hear it from companies that specialize in 4G63's & such, call up Bushur Racing I am sure they have alot of experience. building the badass motors they do..... All I can tell you is from my experiences just like everyone else.

Matt
MFG Racing

http://dsmregistry.com/detail.php?carid=1310

well so far i have decided on this t67...around 40psi/80lbs per minute. stock head gasket also. heres my new mess

Nice... Looks like you have your hands full, we have a few of those... lol... Good Luck..

Matt
MFG Racing

http://dsmregistry.com/detail.php?carid=1310

Originally posted by kelvinb1
well so far i have decided on this t67...around 40psi/80lbs per minute. stock head gasket also. heres my new mess

Captain Caveman

96 RS Turbo 11.414 @ 119.62 MSNS, Crower 2 NA cams, BW366, 10.5 comp, UDP, 60mm TB, W/A intercooler, 3.55 tranny 567.9whp 430tq
97 RS NA 13.188 @ 103.87 MSnS powered 12.5 comp, Crower 3's and 219.4whp with 175tq
98 RS DD 12.5 comp on stock ECU, LTH, Crower 2's, Koni, GC, Hypercoil, DG hats
99 OZ 5sp Stocker 15.856 @ 85.97
99 GS stocker auto 17.7@77mph!

wiki home page:http://www.2gnt.com/index.php?d=bullettdsm

95 Eclipse RS - Sold and In Montana Now
Project 95 GSX - In Full swing.

finally!!!!!!!