this is the problem. i have the obx fuel rail and i have 450 injectors. are they only made to fit the stock injectors or what. the 450s like dont go down all the way its like the end is to long. anyone else have the same problems. i know im a jackass for getting it but just trien to make it fit now that i have it.

no need to post multiple times, people will see it

-----------------------------------------
2011 Nissan Xterra Pro-4x

2007 Kawasaki Ninja 650R

1996 Mitsubishi Eclipse RS-NX 75 shot, AEM CAI, P&P t/b and intake mani-SOLD

1964 Buick Electra 225-all original, all power options, 325hp, 445ft/lbs tq

Originally posted by 96eclipse2nr
no need to post multiple times, people will see it

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

What 450cc injectors do you have? Without having that knowledge then we can't help ya much....

Kevin
The old:


The new:

Seriously, just get rid of the OBX fuel, if you know what you're doing, you would know better than to use that OBX fuel rail, it sucks. Not only does it not lign up when you bolt it to the manifold plenum, you need to get a different O ring for the fuel line so it won't leak. The injectors will sit crooked when it's installed, I would seriously contemplate getting rid of it. But, if you absolutely feel the need to use it, good luck and I hope all works out for you.
~Jeffo



Top end: Ported and polished head, REV stainless Valves, Crower stage 2 cams, Crower valve springs and titanium retainers, SBI rockers and lashers, Fidanza Cam gears, ARP Headstuds.
Bottom end: JE 8.8:1 pistons, Eagle H-beam rods, Balance rotating assembly, Clevitte Rod and Main bearings, Melling oil pump, Crank scraper, carter water pump.
Ignition: MSD Coil, MSD wires, NGK iridium spark plugs.
Bolt ons: MP 60mm throttle body, ported and polished intake manifold gasket matched, Magnaflow catback, high flow cat, Unorthodox UDP, Ground wire kit.
Suspension: Eibach Ground control coilovers, KYB AGX gas adjustable struts, Strut tower bars.
Drivetrain: SPEC stage 4 clutch
Body/Interior: VIS Evo carbon fiber hood, stock red body, stock black 16" rims. Ractive carbon shift boot and ebrake boot, Ractive carbon blue gauges (boost, oil press., volts, and cluster, blue underseat lights.
Installing at the moment: Garrett t3/t04e stage 2 water cooled turbo, RC 440cc injectors, Vortech SFMU, HKS SSQV BOV, Star FMIC and piping, Star manifold, 3" Downpipe, Tial 38mm WG, Walbro 255 fuel pump, Missing link.

Red 97 Eclipse GS (420a) MTX
Custom Garrett T3 Turbo system
Megasquirt w/52 lb/hr injectors & a Walbro 255
Kicker/Alpine Audio (3 amps, 2 subs)
90 Cav 2.2 TBI auto (winter) <- yeah, it's fast

-MIKE-

Stroked 2.2L

do you have the 450cc injectors or the stock injectors because the 450cc i have are from the 1g and the ends are to big to fit on the obx fuel rail. the only thing that i can think of is to bore the holes out so the can fit into them. also like a moron i bought the intake manifold to and the 450cc dont fit into them either same situation probably have to bore out to fit and im not even going to wast my time an either of them. ill just stick with stock intake manifold and get it ported and stick with the stock fuel rail unless there is anyone who can talk me into making them work. screw obx.

-MIKE-

Stroked 2.2L

Mike you didnt even take you own advise here: dont talk down a product you never used.

The 450cc dsm injectors do fit, they work just fine. As search would yield some very good info to getting them installed.

Some facts about the dsm injectors:

1. dsm injectors are low impedance.....did you plan to make or use a resistor pack? you need to.

2. Ends of the DSM injectors are not larger they are much smaller.

3. Are you using 420a injector o-rings?

Most people have been able to lube up the o-rings and force the injectors into the rail. I myself had to trim the injector o-rings with a dermel on the inside of the o-ring to make it sit into the injector groove better. You see on the injectors that they are designed to use a tiny o-ring and the 420a o-ring is huge compared to them.

You need to be extremely careful trimming an injector o-ring because if they leak you are in deep shit.

Terry

dang what is up with the hostility. ok i got the injectors to fit into the fuel rail but what about the intake manifold. any ideas

also i have the obx intake manifold and i dont see how the obx fuel rail can bolt or be supported by the IM anyone with prior experiance please let me know.

You can edit your posts within an hour... FYI.

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

Hostility? I dont see any.

For the obx manifold....that i am not sure i havent seen one. post some picts maybe we can figure it out. if it doesnt have the same mounts the factory manifold has then maybe you are better off sending it back and getting one that does. I dont understand why it does not have the stock mounts.

Terry

ok this is the deal the obx is the same as the venom IM like mikes pics it is almost the same but on mine were mike has his fuel rail mounted my obx mount is to far up and angled all stupid instead of straight i guess i will be sending it back oh well.

Terry, I know how the 450's work, lol.

They are indeed too small and need larger o-rings. I used to use the blue top 450's before. My point was that he was confusing himself on what he was saying on how they were larger when in reality, they are smaller.

As for your manifold problem man, my OBX fuel rail bolted right up to my Venom manifold. My points at which the fuel rail bolts to the manifold are angled too but they did bolt right up, no problems.

Also, you will need to use a resistor pack with those injectors since they are LI.

-MIKE-

Stroked 2.2L

yeah sorry about that i was mixing my words up about the size i do have the resister for the 450cc but yeah i was looking at your pics and saw that my mount was all jacked up. even if i got the injectors straight the mount is way to far up and crooked. ill be sending it back oh well.