How hard is it to install cam gears onto our cars...I have a 1997 Eclipse RS.... just curious.... Thanks

Oh yeah and if it's hard or anybody just went to a shop....what price did you get for the install...and did you get anything else with the install or just the cam gears.....ex. like new water pump, pulley, or even timing belt....

If you are going to install new cam gears, then I would just go ahead and do a 60K service. If you feel really adventurous then you might want to replace the head gasket with an upgraded one...



Eric Madden

I SECOND that notion to replace the head gasket, it's about 3 hours more labor, but it can and will save your engine, would have saved mine. If you decide to do it yourself, buy a shop manual, and not a Chilton's, the real deal from Mitsubishi.

97' Eclipse RS (kinda)

Present mods:
HRC stage III turbo kit (12 psi street, 25 psi track)
HKS 2 1/2" cat back exhaust w/burnt cat
16" wheels w/Yokohomo tires (215/40)
420A engine w/ tooled crank, billet crower rods, and 8.5:1 JE pistons
Head ported and polished, 3 angled valve job
Power-stop brakes w/axis pads
Ebachi Pro lowering kit (1.8")
MSD DIS-2 ignition system w/turbo retard

Near Future:
Stand-alone fuel system
550cc injectors, and fuel rail
TEC III fuel/ecu system
17” Hart racing wheels
KYB AGX struts, w/ upgraded anti sway bars
Rear brake conversion (front to rear, Brembo in front)

I LOVE THESE DSMs
Jay-
wakbrd99@aol.com

97' Eclipse RS (kinda)

Present mods:
HRC stage III turbo kit (12 psi street, 25 psi track) / HKS 2 1/2" cat back exhaust w/burnt cat / 16" wheels w/Yokohomo tires (215/40) / 420A engine w/ tool

how much does the actual head gasket run? any gain from it, what about total ring seal, how much different is this?

www.artexmusic.com

97' grey gs/Greddy EVO catback/Greddy header/AEM cai/afx udp/dropped on 2" sprints

>how much does the actual head gasket run?

depends on the head gasket you want but on average, they are less than 50 bucks, generally around 30.

>any gain from it,

you have have a very small performance gain from getting a thinner head gasket, it increases your compression, but to my understanding it isn't quite as safe.

>what about total ring seal, how much different is this?

I got a total ring seal with my engine rebuild. What it is, is a high HP head gasket that is actually part of both the head and the block. There are groves made in both the head and the block to seamlessly accept a headgasket. It is a much better seal, and can handle as much hp as you can throw at it. But it isn't cheap, my shop charged me around 300 for the machine work, then the gasket would have to be around another 100. But you have to actually pull the engine, and take off all the accessories, and wait a few weeks.. so unless your doing a complete engine overhaul w/turbo, it isn't worth it.

97' Eclipse RS (kinda)

Present mods:
HRC stage III turbo kit (12 psi street, 25 psi track)
HKS 2 1/2" cat back exhaust w/burnt cat
16" wheels w/Yokohomo tires (215/40)
420A engine w/ tooled crank, billet crower rods, and 8.5:1 JE pistons
Head ported and polished, 3 angled valve job
Power-stop brakes w/axis pads
Ebachi Pro lowering kit (1.8"
MSD DIS-2 ignition system w/turbo retard

Near Future:
Stand-alone fuel system
550cc injectors, and fuel rail
TEC III fuel/ecu system
17” Hart racing wheels
KYB AGX struts, w/ upgraded anti sway bars
Rear brake conversion (front to rear, Brembo in front)

I LOVE THESE DSMs
Jay-
wakbrd99@aol.com

97' Eclipse RS (kinda)

Present mods:
HRC stage III turbo kit (12 psi street, 25 psi track) / HKS 2 1/2" cat back exhaust w/burnt cat / 16" wheels w/Yokohomo tires (215/40) / 420A engine w/ tool