1 2 3 4
176 172 191 200

Do I have 2 bad rings? I didn't get to do the oil test yet but I am gonna do that later. SO what do you high tech engine gurus think?




http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

Hmmm... those do sound a little low... Where are you again? High altitudes do lower compression, but I didn't think you were at a high elevation.

But they do sound low to me... any valvetrain noise? Try the leak down test and let me know...

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

yeah that is strange... leaky head/VC gasket? put some oil in ur spark plug holes... see if it goes up... if it does :/



Kory
fasteclipse@cisco.com
aim sn: dukmahsik
Happy Honda Hunting!

The Original 2GNT []D[][]Y[][]D


96 RS


97 GSX

I am at Sea level in Tampa FL. Numbers 3 + 4 sounded okay to me, I think 1 + 2 are the problem. I have a little valvetrain noise but thats due to the regrinds and the shims (.030) not being thick enough.

Valve cover gasket is brand new, I just changed it with the cams. This engine from the head down is only 15,000 miles old. I got a full shortblock under warranty. Then Satan fucked up and I got a new head and valves. I am about ready to sell this car!!! Low compression on a somewhat new shortblock, used tranny already has 1-2 shift grind like the old one. This is really getting to me!



http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

There's only one way you are allowed to sell your car! If you buy another one! I can't have one of the few others building NA cut and run on me

Did you get a used motor put in? or a rebuild? What type of warranty was on it? Are your Cams High lift?

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

the numbers are not really that low. The main issue is the variance between the numbers. It might be worth a retest, but your numbers look more like weak rings vs bad rings. Basically just getting tired and worn out, but the numbers are really not that low.

MuRiX
97 Eclipse GS HRC Stage IV+
Sitting and collecting dust most of the time..
A.D.P.
http://www.murix.com

05 Mazda RX-8
06 Lotus Elise

http://members.home.net/xtatdsm



Fast420A.

did you know that you loose compression with high lift cams?
the Cams make the valves stay open longer, that along with the overlap, your compression numbers will go down (this is why it's a good idea to mill the head to boost the compression a bit up.

your problem is not 172 psi, it's the fact that you have more than 10% difference between the cylinders.

and as Kory said, try to make another compression test, but this time do a wet compression test, put a little bit of Oil in the spark plug hoes (after taking the plugs out) and do the test, if that boosts the compression up, then your rings are going bad, if not, then your problem is else where.

other than bad rings you might have
- bad cams (the loops are bigger in some places than others)
- your lifters are not being pushed down evenly (try shimming the lifters that are still ticking)

I hope that helps

Adel



Ported TB and Intake manifold ** ported and milled head ** PT rockers and lifters ** Crane Drag cams #16 ** Crane valve springs and retainers ** AEM cam gears ** Hotshots headers ** Greddy Cat back ** Iceman CAI ** S-AFC ** and the usual handling mods

The engine was a brand new shortblock a year ago when the first motor blew a rod. Then about 8,000 miles in to the new shortblock the rod was knocking again and Satan took it back in and put in a new crank and bearings. I don't have a warranty on it anymore though. The cams I have are supposedly a high compression drag grind, I don't have high compression yet so I knew I was gonna lose some compression. I am not going to mill the head because I don't want any problems with the cam timing being off a tooth. I am getting high compression pistons to raise it. I have .030 shims in all the lifters, do you think I should put in the .060 because there is still a little lifter noise?
I am going to redo the test with the oil later today to see what happens.

Alright guys, how hard is it to take the engine apart and stick in some new rings? Anybody got any other ideas? Maybe I should just sell it and buy a 1G AWD.






http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

i say next time u do that test, u hit the pipe a cuple times, and u wont care much anymore about it (at least for awhile)

but idunno, dont get too down cuz your numbers are slightly off, it could be a lot worse!!!



Sean G
vegaspimpin 99 gs ounce edition (wish it was a Q P)
http://seangordon1.tripod.com

short ram intake w/custom dual ram air
2.5 catback w/5zigen muff
NGK BKR5E-11
8.5 mm magnecores
AFX UDP in da mail
hurricane gs shiftermod
symborski shifter kit

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

It's just one fucking thing after another. I spent $750 on a used tranny because my 2nd gear synchros were gone and the gears were grinding EVERY 1-2 shift. Now my (new) used tranny is starting to grind at high rpm shifts. I grinded at the fucking track last night on my first run ever. It sucks!

I have my original tranny sitting in the garage. I think I am gonna rip it apart and see what it's gonna take to fix it. I don't want to keep having problems with this car! I am debating on finding a CRX or Hatchback Civic for a Vtec swap. I need to go out and smoke a "cigarette"!!




http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

What kinda tranny fluid you using, I filled up with BG Syncroshift and it worked wonders against mishifting.

Also when you retest make sure the engine is HOT. I got low ass number because I did it when it was cold.


Grrr it's gonna eat you up!
___________________
95' Eclipse RS
AFX Pulley | Autometer Bezel Gauge Holder | Modified A/F Ratio Gauge | B&M Super Oil Cooler | Energy Suspension Shifter Bushings | JAZ Oil Catchcan | Performance Muffler | HKS Air Filter | KYB AGX Shox | Skunk2 Coilovers | FU, RU, RL, and RRE FL Tie/Strut Bars | RS to TSi Rear Disc Mod | RS to TSi upgraded F&R Sway Bar | 97' Spyder Eclipse 5 Spoke Wheels | HKS Standard Blow off Valve | HKS TYPE 1 Turbo Timer | Star Stage 1 T3/T04E BB Turbo Kit | Starion Front Mount Intercooler | Schroth Autocontrol 3-Point Harness | and 1 HiGhLy SkIlLeD DrIvEr! |
Performance b4 Lookz, a car can only be as fast as it's driver! ^_^

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?

LAST EDITED ON 12-Oct-01 AT 10:44 PM (PST)

Well the spark plugs were burning my hands when I pulled them out so I know it had to be pretty warm!
I am gonna retest tomorrow morning when I get home from work and do the oil thingy if they are still lower.

Oh and the grinding isn't mis shifting, it just grinds on the shift from 1-2, usually at higher rpms.



http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

is there a kit you can go out and buy to do a compression test?

ttyl

Matt
Exile Racing Technologies

LAST EDITED ON 13-Oct-01 AT 00:59 AM (PST)

Go to any auto parts store and they have a compression tester. It comes with the instructions but you basically just screw it in to the spark plug hole and crank the starter until the needle on the gauge quits going up.




http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...