I finally finished my side exit exhaust tonight. I've been planning to make this thing for the longest time. I like it. It hums when you go down the road and sounds racey when you whomp on it. I guess it'll quiet down a bit once I take the Bosal off and put the turbo on. We'll see.

My first attempt was just to use one glasspack - Flowtech Red Hots 2.5" diameter, 18" core, 24" overall. It didn't quiet it down enough. I'm using a high flow catalytic converter and my mistake was that the cat doesn't quiet things down at as much as I though it was going to.


So i ordered another glasspack. The new one is a Summit glasspack 2.5" diameter, 14" core, 18" overall. This was the ticket...at least for my tastes. It makes it sound obnoxious but not deafaning.


I put it in the garage after the test run to let it idle a bit so I could check for leaks and whatnot. When I went upstairs my wife said "You rattled the windows". Oh, it looks pretty cool on the car too.









95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

I always wondered if it was possible... u da man!
do you scrape a lot?

1995 Eclipse RS

I've only been running the side exhaust now for a few days but no scraping yet. Theres about 4 inches of clearance from the bottom of the 2.5" diameter pipe. Thats with a stock ride height too. It may become an issue. I figure that if it does become an issue then I'll just run one, possibly two oval pipes for the tip.


95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html

Cool!!! Too bad you can't leave your beer next to the car when working inside the driver side or the door panel lol I still think it's PIMP!!

1995 Eclipse RS

if you were low at all you wouldn't be able to have that exhaust like that.

youd go over a speed bump and rip it off. its cool i suppose, but just don't make sense for a practical application.

nice job jim!!

Evan B
97 GS
90 GSX
Stamford CT
EvMan2345@aol.com

Sweet ass dOod.

I eat emo kids for breakfast

1995 Eagle Talon (SOLD)
72' SuperBeetle
72' Standard Beetle
56' Deluxe Beetle

wow MJ, that's tight. Just don't be getting CO poisoning on us. If you feel faint and look flushed, get outta the damn car and breath some fresh air!

I don't know how you can put up with the noise though. I swear this car is giving me tinnitus with a regular magnaflow

2gnt: '99 RS-T, killed by a toyota, pending rebuild...
Daily: Volt
Daily #2: '99 EVG ebike- STOLEN by PEDRO

thats cool dude. i was thinkin bout either doin that on both sides at 1.5 inch on each or 2 and cut another hole in my stock rs rear bumper and make 2 fat ass ones there. how loud is it when u gun it though? unbelievably loud? cause thats next to ur fuckin ear dude.

VIDEO!!!

_____________________
98 Silver Eclipse RS ATX
CAI, header, bored TB, Apex N1, Pro-kit/Tokico combo, custom lower tie bars, cross drilled/slotted rotors

You could also go through the stock side skirts, that would be cool.

pimp

and you sir have an e-mail.

Member # 751


FOUNDER of the Central Cali chapter of 2GNT!
(I got kicked out after I refused to go Cow tiping) - Hehehe you know who this is for

different

but how did you support the end? That's a lot of weight to wangle dangle out the side there you must have did something.

getty up

-kent-




'98 Talon...gone, but not forgotten

Thanks guys.

I have a perfect spot for testing the speed bump clearance. My brother in law has a nasty one in his development. I'll take a ride over there today and see how it handles it.

As far as the support is concerned, I guess the first point of support is on the cat. I have a high flow cat and what I did was weld a couple of j hooks on the sides so it mounts to the factory rubber on each side. For the catback I installed 2 universal hangers. Theres one at the bend and one at the end. For the one at the bend I removed the holy part of the universal bracket entirely and drilled the hole in the rubber big enough so it fits on the factory hook. For the one at the end I attached the bracket on the inside of the body right where the tailpipe exits. Heres a pic of the bracket locations.




95 Eclipse RS : 5 speed
15.7 @ 87.9mph
Jeep TB writeup - http://www.dimensia.com:81/jimbo/JeepTBfor2gnt.html