i have a 95 eclipse gs and i bought an intake off ebay and i cant figure out how to install it.??? can someone explain how to connect the new inake tube to the throttle body??? thanks

there should be a rubber connector piece. Slide one end of that onto the throttle body and the other half onto the intake. There should be some clamps that go over the rubber piece, tighten those up.

yeah i tried that but the rubber piece is too big for the throttle body??? the intake tube is alot larger in diameter that the exit to the throttle body. what do you think?????

like he said, put the rubber connector on the end of the tb and then put the intake pipe in the other ond of the rubber piece and tighten the clamps. If the intake pipe is larger than the tb, just mkae sure it isn't right up against the tb. It should work as long as both clamos are on tight.

winter project: custom t3/t4 turbo and some others

Nevermind all the ghey wire ties. The people responsible have been sacked, had their revenge, been sacked again, and it's just so damn big because I can so there.

You just need to make sure you get the clamps on the coupling that goes from teh tb to the intake tight on both sides. You might also want to get some hose to put over the upright there for the battery hold down. Mine was almost halfway worn through from rubbing after about 6 weeks....

Lets just say this... I'm over 100whp and soon to cross 200whp. Thanx 2GNT! Now if I could only learn to prove it.

that was lame....but anyway...u get what u pay for....

Lets just say this... I'm over 100whp and soon to cross 200whp. Thanx 2GNT! Now if I could only learn to prove it.

the size of my intake tube is alot larger than the throttle body??? the size of the rubber piece is larger thn the throttle body. i mean alot larger. am i sopposed to use a part of the stock intake to work this one??? someone help me please!!!!!!

maybe you should post a pic or a link to the ebay auction so we know wtf you're talking about.

You may have got the "CAI Extension" which you attatch to the end of your stock rubber intake hose where the box used to attatch.

I dunno, my AEM fit perfectly. I posted a thread about 2 weeks ago warning people not to buy eGay intakes

__________________________________________
~Chris
03 SRT-4

I have issues.....he got a cheap (as said above) egay intake and how about that it doesn't fit right....I feel for the dude but as said before u get what u pay for

i got some cheap little $5 intake off ebay a few years ago.... it was basically a 3" civic intake that didnt even fit right. someone correct me cuz i know im wrong but the throttle body is somewhere around 2" if not 2" so the connector that it came with was 3" on one side and 2" on the other. the smaller side went on the throttle body and the larger one went on the intake.... either way you got an ebay intake which means your going to have to MAKE IT fit....

if that doesnt help i dont know what to tell you cuz you confused the fuck out of me

1998 GS
Mods: Cold air intake, Ported/polished stock intake manifold, AFX 55mm TB, Pacesetter header,
Custom Magnaflow cat-back exhaust system, AFX Underdrive pulley,
B&M short throw shifter(cut/welded), Symborski Shift Kit, Solid front motor mount, Monster ground wire kit.

Status: Finally up and running!

yea that ^^^ is what i was going to say. go to autozone or like someone else said home depot and get a 3" to 2" reducer. problem solved.

Here's the reducer they're talking about. This is definitly the best choice. Check out this webpage for more info:
http://store.summitracing.com/default.asp?target=department.asp&d=18&x=16&y=8






"Life isn't like a box of chocolates...it's more like a jar of
jalapenos.
What you do today, might burn your ass tomorrow."

Well damnit my cheapass ebay intake fits perfect, looks ok too.