ok...lastnight i was working on a mod which consists of doing some ecu pin soldering... in this process i accidently bent pin #14 which is non exsistant on the harness itself. When i tried to bend it back slowly the pin broke off.... I didnt think anything of it cause like i said it wasnt on the harness.... when i went to start the the car the fuckin thing sounded like a V8....almost to the poiint where it sounds like a misfire.Ok ill check the spark.... all good...i am getting a Cel but my damn generic obd2 scanner wont pick it up...so i was thinking.... is pin14 supposed to be terminated at the harness?is there any way to get in there to solder a new pin in?
I havent tested drivability yet.... i just know that if i dont give it some gass (about 1200rpm) she'll stall...

As far as i can tell all other pins are making good connections.
Let me know if anyone has any ideas....


thx
jake

AEM cam Gears,MSD ignition,Chikira 4-2-1 header,Custom 2.5" exhast,Pacsetter hiflo cat ,head p/p , intake p/p 2mm oversize tit valves , t/b p/p , shiftkit , TQ lockup mod , and much mor

bump

Have you left the car on long enough for the ECU to readapt it's long term fuel trim (a good 15 minutes of idleing, and some driving)?

If you have then sounds like your gonna have to replace your ECU.

Joel Baldridge, ASE Certified Master Technician, Audi Certified Expert Technician

what other mod did you do? If the pin you broke did not have a harness wire attached to it then i doubt that is the problem.

Now pin 14....top or bottom harness connector (96-99)? or do you have a 95 (1 large connector)? Accordign to the schematics i am looking at for a:

95 N/T ECU:
pin 14 receives a 12+ signal from the distribution wiring.

96-99 N/T ECU:
no A or B 14 pin

96-98 2.4L non Turbo ECU:
A14 goes to a fuel injector #2 to be exact.
no B/C/D 14 pin

give me some more info and i will try to help.

Terry

the reason the OBDII genaric scanner will not detaect your code is because the code is vehicle specific, therefore you need to have a scanner like trhe snapon mt2500 that will read the vehicle not just a generic code set. go to a shop or the dealer. if you call a shop make sure they have the cartridge for your car. if you have a mitsu then they might not...the asian cartriges are 3000.00. if they have a genesis then it comes with the asian cartriges.

Terry

ya i use one on campus.... its just getting the car there thats the prob..

AEM cam Gears,MSD ignition,Chikira 4-2-1 header,Custom 2.5" exhast,Pacsetter hiflo cat ,head p/p , intake p/p 2mm oversize tit valves , t/b p/p , shiftkit , TQ lockup mod , and much mor

Terry, what are you using for pinouts?

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

ok here i is... its pin 16(sorry miscounted) light green w/ red stripe... i think it may be an injector refrance but not sure..its a 97 (like i said obd2) i can replace it if i can get the pin connectors out of the ecu somehow.... anyone done this b4? i really dont have the cash for a new ecu...

where did u get those schematics?

jake

AEM cam Gears,MSD ignition,Chikira 4-2-1 header,Custom 2.5" exhast,Pacsetter hiflo cat ,head p/p , intake p/p 2mm oversize tit valves , t/b p/p , shiftkit , TQ lockup mod , and much mor

It's injector #4.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

thaught it was an injector thnx man....


now all i gotta do is figure out how to get in the damn ecu w/o busting it up too bad..



jake
AEM cam Gears,MSD ignition,Chikira 4-2-1 header,Custom 2.5" exhast,Pacsetter hiflo cat ,head p/p , intake p/p 2mm oversize tit valves , t/b p/p , shiftkit , TQ lockup mod , and much mor

did you break the ECU pin or the pin in the harness connector. dark one i was looking through the chiltons schematics and the Dealer book schematics on disc.

Terry

Only the ECU side has pins. The harness side is just female receivers.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/