i changed my filter about 6 months ago, lately my car has been acting as if it's clogged again. has this happened to anyone (short filter lifespan)? is there another filter of some sort in the fuel system that i haven't changed yet?
#67433, "RE: Fuel filter...only one?" In response to Reply # 1
engine runs smoothly if i gradually increase throttle - so there's hardly any load... any decent acceleration results in misfire/hiccup at all rpms. drivable but definitely in limp-mode. i'm almost positive the plugs, wires, and coil are in good shape, and because of the slow smooth revving i'm fairly sure it's not ignition or timing related. guess i'll swap out the filter again this weekend and see if it helps.
#67440, "RE: Fuel filter...only one?" In response to Reply # 2
Try running some injector cleaner before taking anything apart. It might save some trouble. If that doesn't work, then try the filter again. Good luck!
#67456, "RE: Fuel filter...only one?" In response to Reply # 2
Originally posted by Blk95GS engine runs smoothly if i gradually increase throttle - so there's hardly any load... any decent acceleration results in misfire/hiccup at all rpms. drivable but definitely in limp-mode. i'm almost positive the plugs, wires, and coil are in good shape, and because of the slow smooth revving i'm fairly sure it's not ignition or timing related. guess i'll swap out the filter again this weekend and see if it helps.
It sounds like wire/plug problem to me. It sounds like what everybody had/is giong through. I've had the same thing happeneing to me a while back and comes back every now and then. check ignition coil, plug wires, plugs. So if you accelerate slow, the car would slowly go right? And when you floor it, it misfires all the way? or would it run hard after like 4,5k rpm? give more detail.
#67481, "RE: Fuel filter...only one?" In response to Reply # 4
Oops, I forgot about the flat fuel filter that's attached to the fuel pump. If you've verified that the ignition parts are good, then you might want to check for vacuum leak(s) and/or do a compression test.
___________ Kon C
"Sometimes, a man has to do what a man has to do."
#68189, "RE: Fuel filter...only one?" In response to Reply # 7
save yourself the hassle of taking crap aprt on the fuel system and do it right....hook up a fuel system gauge and see what your fuel system pressure is at idle and at load.
then go from there.
low pressure means blockage or bad pump or even bad regulator.
#68278, "RE: Fuel filter...only one?" In response to Reply # 8
Originally posted by Star Turbo Talon save yourself the hassle of taking crap aprt on the fuel system and do it right....hook up a fuel system gauge and see what your fuel system pressure is at idle and at load. then go from there. low pressure means blockage or bad pump or even bad regulator. Terry
yep. follow his instructions. ^^^^
_______________________________________ AZ2GNT JOE - Lifted 95 Jeep Grand Cherokee www.nagca.com
#68280, "RE: Fuel filter...only one?" In response to Reply # 9
I say get a multimeter and check the coil pack. Unplug the harness to the coil and touch one lead to the center pin, then the other lead to an outer pin. You should get .51-.61 ohms for each pin. Then check the resistance across the towers. 1 and 4(in the back) and 2 and 3(in the front). Should be 11.5-13.5 kilo-ohms. If these numbers aren't correct, you need a coil pack. The MSD replacement is cheaper than stock. Also make sure you check your meter before you start and see that it's accurate.
Lets just say this... I'm over 100whp and soon to cross 200whp. Thanx 2GNT! Now if I could only learn to prove it.
#68365, "RE: Fuel filter...only one?" In response to Reply # 10
Originally posted by Dave41079 I say get a multimeter and check the coil pack. Unplug the harness to the coil and touch one lead to the center pin, then the other lead to an outer pin. You should get .51-.61 ohms for each pin. Then check the resistance across the towers. 1 and 4(in the back) and 2 and 3(in the front). Should be 11.5-13.5 kilo-ohms. If these numbers aren't correct, you need a coil pack. The MSD replacement is cheaper than stock. Also make sure you check your meter before you start and see that it's accurate.
i'm not sure if the .51-.61 is right. i am having the exact same problem. i thought it was the coil but i have bought 2 new ones and they both read .81 . on my car i replaced the wires, plugs, coil, map sensor, crank sensor, fuel filter(w/gst filter), fuel pump(255), rewired the fuel pump and the block but it's still doing it. i have also ran about 7 bottles of injector cleaner and a bottle or two of HEAT. its still doing it. i don't know what it is but it sucks ass.
#68394, "RE: Fuel filter...only one?" In response to Reply # 11
i figured it out, at least on my car. it was the wires. seems that one of the cyl. 2/3 wires didn't have enough length inside the boot. so when the boot is pushed in the spark plug well to where the valve cover stops it, it wasn't making contact with the plug. hope this makes sense. if it doesn't, pull all your wires and then put spark plugs into them and make sure they are all the same length. if one is shorter, thats your problem.
Search
Printer-friendly copy
1 User in Chat
