Where do the shims go? I think they go under the lifters but I want to make sure!!!

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

Under the lifters is correct. They need to have a hole so oil can pass through them. Make sure the are all the smae thickness too. Good luck, if you have any other questions post here or try to get me via AIM or email.



http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

Whats your email? mine is Talon95Stang@cs.com

How much should I get my head milled????(.010)

Thanks alot!! I'm going to get my head milled and a 3 angle valve job done tommorrow for $100. Do you think I should get my head ported and polished? or just get my intake ported and polished. The shop wants $400 to port and polish my head. I think I'm just going to mill my head and get the valves done.

venomtalon@aol.com

Performance Mods: Custom CAI, Jeep 60mm TB, Ported Intake Manifold with Jeep TB match, 5 angle valve job, Head milled .020, Regrind Cams, PT Lifters and Rockers, AEM Cam Gears, OBX Wires, NGK Plugs, AFX UDP, OBX Header, OBX

>Whats your email? mine is Talon95Stang@cs.com

OhShootUhh@aol.com

>How much should I get my
>head milled????(.010)

Milling amount depends on the compression increase you want. You probably wouldn't even notice .010 of milling.
Here are some static compression numbers on a stock gasket (.040"):
.068" mill= 11.5
.053" mill= 11:1
.039" mill= 10.6

These numbers work in 2 two ways. Milling/gasket thickness is one in the same. It's all about taking volume away from the combustion chamber. Our engine, stock, has a combustion chamber of about 51cc. If you reduce that then compression is raised.

If you go to the extreme on the milling then you will HAVE to have cam gears to fix the cam timing which will be off. Usually around .050 of milling and the cams will be off 1 tooth. You should have cam gears with regrind cams anyways.


>Thanks alot!! I'm going to get
>my head milled and a
>3 angle valve job done
>tommorrow for $100. Do you
>think I should get my
>head ported and polished? or
>just get my intake ported
>and polished. The shop wants
>$400 to port and polish
>my head. I think I'm
>just going to mill my
>head and get the valves
>done.

Port and Polish is a good thing to do. If you can afford it, do it so you don't have to take the head apart again to do it later.







http://hometown.aol.com/ohshootuhh/

All Motor Beast in need of MAJOR TUNING

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

If you have them poort and polish the head, I reccommend havign them gasket match everything... again so you don't tear it parrtt later

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.