|
Hello Everyone.
At first, I posted in "auto Tranny" section, but guess no one cares about my situation over there, so I repost it here.
Please reply with inputs!!
Gil
As you all been reading, I been doing an engine rebuilt for my g/f's eclipse for the past 6 weeks. It's getting TOOO long, and I am just .... VERY TIRED OF IT.
I got it back into the car today, and break in the car (15 mins start) and everything is cool... BUT.... VERY SADLY, the car won't move.
Ok guys, now I have to ask all of you a BIG favor, you guys have to tell me everything you guys konw about ATX tranny and engine rebuilt....etc....
------------------------------------------------------------------
A breif explanation on my car's rebuilt history first:
I got the car, and I spun her bearing, so much that the piston hits the head, and fucked up the whole crank.
I took the everything off, but leave the tranny in the car (only the engine out) And at first, I don't konw there were 4 bolts that connect to from the flywheel (engine side) to the Torque Converter (Tranny side) So I think I BENTED it (that's my problem I think)....
Anyway, after 4 hours of struggle, I got it figure it out, gave it to a shop for New ring, new bearing (all bearing, main, rod) and hone, clean, cut the whole crank, etc...
I put everything back, and the first 4 times I put the engine back, I CAN"T turn the crank after the flywheel (the big gear) is bolt to the Torque Converter. My 4th or 5th time of reputting the engine back into the car, it turns, so I was like.... THANK GOD....
After everything is in, and hook EVERYTHING back, I start the engine... ALL GOOD, sound good and everything, BUT I hear trick, trick, trick, NOT from the engine, but from the tranny....But anyway, I keep it run at 1500RPM for first break in. Then I cool it down and go for a test drive....
---------------------------------------------------------------
The sad story begins... no matter what gear I put the car into, the car WON"T MOVE, it's like the engine doesn't hold to the tranny. I made sure the cable is connected, when it shift, the cable to pull. Also when I shift to every gear, like 'park', the car won't move, and so on...so the tranny to the wheel is FINE.
Also, after a while of break in, the tranny has ALOT of smoke comes out, from the dip stick of the tranny and etc....
Anyway.. here is the problem:
1) Tranny has tricking sound
2) Engine turns, but car WON"T move in any gear
3) Smoke comes out for 5 minutes, but now it has no more smoke...
(I think maybe too hot, and smoke from WD-40 or etc... Hope so)
So any input???
Is it something EASY??? or did I fucked up the tranny from benting the TC when pulling out the engine??
Please reply....I AM CRYING (soon)....... engine is fine from spun bearing... 6 weeks..and now...it tells me "I FUCKED THE TRANNY UP"....wtf....ARR>>....
PLEASE HELP
Any input will greatly appreciated.
Gil
~~~~~~~~Modification~~~~~~~~
Performance: MegaSquirt v3.0 Fuel & Spark, 8.6:1 JE piston, Eagle Long Rods, SPEC III Clutch, EVOIII B16G, FMIC, Aeromotive 1:1 FPR, Walbro 255HP, 680cc Injectors, 2.5" DP, 3" Magnaflow Cat, 3.5" Greddy EVO CatBack, Greddy Electronic EGT,FUEL,BOOST,A/F gauges...
Interior: Racing Seats, Metallic Interior, 15-Speakers System, Keyless, Dynomat Insulated, Neons...
Exterior: 1999 Body with turbo wing, Halo Projector Headlight, 4300K HID, 17" Mille Rims, GSX Calipers...
Coming Soon: Water Injection, Redo Undercarriage, Repaint Exterior
$240 For New Complete GSX Calipers Kit (Calipers, Bracket, Shim, Pad, Bolts, etc) Email Me If Interested!
1995 RED Eclipse GS-'T': Stage VI 20PSI
2010 Audi S5 Quattro
|
Search
Printer-friendly copy
0 Users in Chat
