ok i have one and its gonna be installed soon (i hope) but i have a few questions for everyone that already has it first. i wanna know whats causing this squeeling shit so here goes.

1. does it squeel?
2. how long have you had it on?
3. did you put it on yourself?
4. did you heat it to put it on?

thanks all
-JASON

I need money...wanna donate?

-jason

i've had it for 18 hours, it does not squeal, i put it on in 2 1/2 hours, buy a 3 inch M12 bolt and some washers to install it (press it in place) i heat it but it did no good, i used a propane torch too,

Rest In Peace Heidi Doggy

I've had it on for a while I need to retension the belts I have a little squeal, and plenty of room left to adjust out if I remember so I should be good.

And SEA97GS... no no no no no no... don't use a propane torch on aluminum!!! You run a risk of warping the pulley of you don't heat it evenly.

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads, S-AFC, A/F Meter

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins., EGT

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

Michael - I didn't use any heat at all. I wasn't about to mess up that wonderful piece of machining!!!

Sam Crawford
SEA97GS - 15.785@88.20MPH
NW.DSM.ORG
HotShot Headers-Custom 2.5" exhaust-MSD 8.5mm plug wires-NGK Plugs-Nitto NT555R Drag Radials on RX-7 wheels-Eibach ProKit Springs-Tokico shocks-front upper STB

97 Eclipse GS-15.463@88.57MPH - RIP
92 Talon TSi AWD-12.927@105.47MPH

Sorry SEA97GS, I meant jamesman. I apparently wrote that reply before I had my morning coffee and grabed the wrong screenname... many apologies.

Hey BTW did you ever get the solid front mount, and others (igniton?) installed?

"Claim Victory in your heart, and the universe will follow."
Michael J. Kulaga e-mail: Michael_97RS@2gntDSM.zzn.com
aol IM: MJKulga Website: http://highlander.dsmpower.com/

Injen CAI w/ K&N Breather Filters, AFX UDP, 55mm TB, GS-T Muffler, FU/RU/RL STBs, Front NRG Susp. Motor Mount Ins., Red Silicone Hose Kit, 8.5mm Magnecor Wires, Bosch Rapidfire Plugs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads, S-AFC, A/F Meter

And in my Room: Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, SS Clutch Line, Rear Motor Mount Ins., EGT

Waiting for from RRE: Front Lower Tie Bar

Waiting for: Intake Manifold being ported/polished

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

Not a problem. I know how mornings are without caffine!!!

Doing the motor mount tonight. Tried doing it over the weekend and didn't have the right socket. And I also don't have anything to support the tranny with, so I'm going to a friends house. I'll report if this helps 1/4 times cause I'll be at the track a couple times this week.

I've still got the MSD sitting in a box in the laundry room due to no time either. I'm going to take that to a mechanic friend of mine to install. I'm not good with electronics and don't really feel like frying something if I don't have to. I know it's pretty straight forward, but I have no comfort level with it.

SEA97GS - 15.785@88.20MPH
NW.DSM.ORG
HotShot Headers-Custom 2.5" exhaust-MSD 8.5mm plug wires-NGK Plugs-Nitto NT555R Drag Radials on RX-7 wheels-Eibach ProKit Springs-Tokico shocks-front upper STB

97 Eclipse GS-15.463@88.57MPH - RIP
92 Talon TSi AWD-12.927@105.47MPH

I've had mine for about 2 months. It does squeak a little bit, but I also know that the adjustments for the accessories are maxed out. That tells me that the belts that come with the kit are a little long. That can easily be fixed.

As for time wise.....couldn't tell you. The timing belt was getting installed at the same time so all those parts had to come out anyway. Probably 4 hours total. No heat was needed to install the piece either.

So far this year, I've averaged about .15 faster in the 1/4 mile. I've already been in the 15s 4 times this year. Barely, but still 15s. The time below is from '99 when the motor was newer and had more power.


SEA97GS - 15.785@88.20MPH
NW.DSM.ORG
HotShot Headers-Custom 2.5" exhaust-MSD 8.5mm plug wires-NGK Plugs-Nitto NT555R Drag Radials on RX-7 wheels-Eibach ProKit Springs-Tokico shocks-front upper STB

97 Eclipse GS-15.463@88.57MPH - RIP
92 Talon TSi AWD-12.927@105.47MPH

doesnt squeal at all.
great bang for the buck

'98 GS AT
Magenta Gray Pearl
NGK Plugs and Wires
AEM Short Stack
GS-T Exhaust
Bored throttle body
Bored Intake manifold
AFX underdrive pulley
RRE Front Lower Bar

'98 GS AT.Magenta Gray Pearl.Accel Spark Plug Wires.NGK Plugs.AEM Short Stack.GS-T Exhaust.AFX Underdrive pulley.RRE Front Lower Bar.Tenzo Rear Upper Bar.Tenzo Rear Lower Bar.Tenzo Front Upper Bar.Energy Suspension Bushings.Energy Suspension Motor Mounts.

I used a cheap old toaster oven to install my afx pulley. I used an 100ft extension had the oven right next to the car. I then turn on the oven to 500 degrees set the timer to 1 hour then viola "ready to install pulley". I used a some cheap leather gloves and couple of oven mitts to install the pulley. The pulley slide in VERY easy.... Wait for the pulley to cool than install the belts.
I also adjusted the P/s pump to its mAx height than ajusted the tensioner till the belts were taut.(about 1/2" deflection) same for the alternater.
So far its been about 1week + ,Ive tested thru 2 heavy rains, mud,spilled about 1qt of power steering fluid on the belts (don't ask), radiator fluid (busted hose) and about 1000 miles of interstate hi spped usage. so far no sqeeks. Basically i'm just checking the tension on the belts and ajusting as needed.
--For the toaster,i just washed it and used to cook a tv dinner later that night.

Forget the pulley, I want one of those toasters!

I've had mine for about a month now.....p/s and ac belt is sqeeking like a mother, I can't stand it anymore. I've adjusted it about three times and doesn't help....cheap Bando belt I think. I'm changing it out Sunday.

John
AOL IM: John99RS
john99rs@hotmail.com
http://johnseclipse.homestead.com

http://www.cardomain.com/ride/3130861

Had a shop do it and they used a harmonic balancer installer device thingie. Anyway I don't really notice it there anymore but my tension pulley on my accesory belt is squeaking and I need to replace it. Mine came with some big ass belts that I later changed to some smaller Goodyear belts which gave me plenty of room to adjust the tension on the alternator. I'm pretty sure the belts aren't the ones that are causing the squeak it's that damn tension pulley, when I squirt it with belt dressing the sound muffles.


95 Mitsu Eclipse RS
AFX Pulley | B&M Super Oil Cooler | Performance Muffler | HKS Air Filter | KYB AGX Shox | Skunk2 Coilovers | FU, RU, RL, and RRE FL Tie/Strut Bars | RS to TSi Rear Disc Mod | RS to TSi upgraded F&R Sway Bar | 97' Spyder Eclipse 5 Spoke Wheels | HKS TYPE 1 Turbo Timer | Star Stage 1 T3/T04E BB Turbo Kit | Schroth Autocontrol 3-Point Harness | and 1 HiGhLy SkIlLeD DrIvEr! |

http://www.hadesomega.info -car specz and movies 95 Eclipse RS | 76' 280Z | 89' MR2 | 99 Neon | 91 Zephyr
Who sez FF can't drift?