I know this was discussed a week ago, but I thought of another question. When you get the port and polish - does that include the manifold and the runners. I just bought a spare intake manifold with upper and lower runners and I want to know if I need to buy all the gaskets and what parts need to be shipped to ARD.

Thanks,

Tim
trwebb26@yahoo.com
White 1999 GS - Manual Tranny
Mods: B&M Shifter, Symbroski Shifter Kit, RRE SS Clutch Line, AEM Short Ram Intake, Clear Side Markers, GS

Send the manifold gasket set (upper and lower) and TB gasklet they will port match it. do the runners and the TB inlet.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, Crane Ignition Amp

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

Do you guys know if the manifolds are the same between 95 and 96 Or did they change them to take the OBDII for the returnless fuel system?

Engine mods-
RS Akimoto short (P.O.S.!) intake, Greddy Sport Cat-back ex.
Suspension-
Ground Control Coil-overs,KYB AGX shocks, RS Akimoto strut bar(front) TSW Trouphies 18x8,Nitto 555's.
Exterior-
Paint! C.F. Hood, Z3 fenders, Street Fighter Gen 2

Remember me?

accually you dont need to send the gaskets with the manifold.. ARD has a set on hand to port match.. ive got mine waiting to be installed come this next weekend.. cant wait.

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

Ask before you send to see about the gaskets. I remember something about this coming up a week ago.

All the manifolds are the same across the years. The fuel rail is what is different on the 95s.

-"Easy Mac"
05 Mazda RX-8 (RR8 #88)
99 Eclipse RS 398whp & 372lb-ft

I emailed them but havent got a response yet, only been a few days though. Can they bore the tb and put a new butterfly valve in like howell or do they just clean it up a little? I have my intake manifold and tb off the car and am ready to ship it somewhere... maby ARD, maby Howell... choices.. choices...

ARD has accually done a tb for me, but it is not the same as the overboring done by howell.. mainly what is done is that they increase the size a little and polish it up retaining the lip in the middle of the tb.. here are some pics..



stock on right



i will take some better ones when i get a chance, but it is a bit larger and more or less polished than stock

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

hmm, if ARD cant bore to 55mm and install a new butterfly valve, i guess its going to howell...

i dont think that they can't they just wanted to try a diff approach to it.. im sure they could bore it to 55mm if you asked them.

-Jason

97 Talon ESi-T (forever in progress...)


95 GS (Gone)
16.74@83.18mph
119.8 whp - 113.3 lbs/ft


2GNT #677
My Wiki Page: www.2gnt.com/index.php?d=Iamnotwhoiam
Pictures: http://picasaweb.google.com/iamnotwhoiam/Talon/

well, i told them what i wanted done and they just replied with a price an an address... so I guess they can, we'll see if they do it right

so Brad how much does it cost to have the tb bored and the manny p&p with the gasket matching

I edited to the wiki!

I dont know what their avg prices are or if they are cutting me a deal or not, or will do what they agreed to, but they said 150 for the p&p, gasket match, and rework the tb w/ new butterfly valve, I just tracked the manifold w/ ups and its been there for a few days now, I'll keep you posted when its recieved and post some pics..

btw how much hp are you up to now with the stage 5 i'm really thinking about building a monster too where are you at now hp wise

I edited to the wiki!