Read the subject.


______________________________
current status unknown

http://hometown.aol.com/ohshootuhh/

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Drop in K&N Filter and open airbox
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

I am almost positive you can, Kyle. It's just always something all the 4g63 guys recommend. Moreover, there's only two wires that run from the probe so if the hookups don't mate exactly right...I'm sure you'll be able to solder with a little cut and snip. But they're just probes on each end, so I'm sure it'll be cool.

http://www.dsmtalk.com/forums/showthread.php?s=4eb0780f89034d09f4f30d8f528a4366&threadid=6602&highlight=westach+and+probe+and+autometer+and+guage

_____________________________________
Jason ESi-T

04' BMW 325Ci
91' Nissan 240SX
98' Eagle Talon ESi (sold)

Thanks bro! I'll try it out and let everyone know.


______________________________
current status unknown

http://hometown.aol.com/ohshootuhh/

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Drop in K&N Filter and open airbox
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

but there conversation about tappin cyl 1 3 inches away is wrong for us, right? we need to tap cyl 4 x inches away from head?

fill me in, i mihg tbe confused, or right on top. sumthin to do with intake airflow and heat capability??

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

Back in the day when people blew their engines more often, it was generally accepted that the #4 cylinder was the hottest and probably most susceptible to detonation. That would be the cylinder closest to the driver's side. That's why we at 2GNT all recommend your probe to be tapped on that runner.

Applying that same approach to any other engine would be unwise since all engines are different. Moreover, the 4g63's hot spot may very well be different than our own.

_____________________________________
Jason ESi-T

04' BMW 325Ci
91' Nissan 240SX
98' Eagle Talon ESi (sold)

Yes you can use the Westach probe, I do. The ends need to be cut so you put bare wire into the magic box It's a nice set up, the Westach probe reachs nice and fast.

Yah a couple inches from the head and in the #4 runner. Should be the hottest due to EGR and coolant flow.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, Crane Ignition Amp

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

I use that setup as well. No problems. But, as far as EGT placement, I got some advice from a friend. I didn't use it, b/c he told me too late, but it makes sense. Put the EGT where the runners come together. That way, if one cylinder is going lean, you will get a slight difference.
If you just tap one runner as I did (and as suggested above), you'll never know if one of the other 3 cylinders is running lean. Sounded like a good idea to me.

99GS MT | Star Stage 2 | GC coilovers | HurriganeGS tie bars | Tokico Illuminas | 17x7 Enkei RS5 | Baer track brakes |+

Problem with that is exhaust gas will cool significantly by the time you hit the collector and at that point it's too late to tell there's a problem and and if one cylander is running too hot one cool the average temp will be lower so, I say best bet is tap the hottest runner, next best is 4 EGTs

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."



Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold 1/2, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads, Crane Ignition Amp

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.