there's this one part on the injen intake that's suppose to bolt on. Did yours fit with ease? cuz mine doesn't seem to want to move in close enough to get into that bolt, and i'm afraid of leaving it loose because of the thing that it's already suppose to be holding down will be fluttering around loose.

any tips?

tia.

16.1 @ 87.11
http://www.virtuallyinfamous.com

ARD 57mm tb and p&p manifold, Neuspeed STB, Pro-kits, Illuminas, Injen CAI with K&N, 2.5" pacesetter catback,
AF/X UDP, Rear STB, Powerslot rotors, RRE SS Brakelines.

unbolt the battery tie down, and push it toward the dr. side door (corner). that might be the problem.

also, make sure the intake doesnt rest on the cam angle sensor.

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

Let me guess the bracket that bolts to the head? Just bend it, the metal is soft enough that you can bend it into place and then bolt in with ease.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

shoot.. DUH on me. haha, i shoulda tried to bend the bracket.

thanks for the tips!

i'll try both tomorrow when there is light.

16.1 @ 87.11
http://www.virtuallyinfamous.com

ARD 57mm tb and p&p manifold, Neuspeed STB, Pro-kits, Illuminas, Injen CAI with K&N, 2.5" pacesetter catback,
AF/X UDP, Rear STB, Powerslot rotors, RRE SS Brakelines.

there have been a lot of people have problems with their intakes rubbing on the battery (I know my AEM did when i first installed it). I had to take off the battery cover to keep it from rubbing. I don't know how the injen is, but you may have to do the same.

Hope this helps,
Tim

Tim
trwebb26@yahoo.com
White 1999 GS - Manual Tranny
Mods: B&M Shifter, Symbroski Shifter Kit, RRE SS Clutch Line, AEM Short Ram Intake, Clear Side Markers, GS

Oh and if it rubs on the battery tie down bar... which mine did I covered the bar with vaccuum hose so it didn't scratch the metal anymore.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.