I've got the electronic autometer oil pressure guage. Where did you guys put the sensor? and did you just use a T tap?

____________________________
My $.02
95 GS

Yep I have two T fitting back there one for oil pressure one for oil temp. Eventually I'll put a fitting in the pan for the temp. But for now it's T'd in the back with the tsock sender.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

did you just cut the line then? or were you able to just loosen it and add the Ts in there?

____________________________
My $.02
95 GS

If you go to my website and look under "gauge install", I have a detailed write up on what to do and where to get the parts. Check it out.


http://johnseclipse.tripod.com/welcome

http://www.cardomain.com/ride/3130861

One other thing. The stock sender is a pain. I had to go and get a oil pressure socket. If you need to borrow it or ned a hand let me know.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.

>I've got the electronic autometer oil pressure guage. Where
>did you guys put the sensor? and did you just use a T tap?

Here is how you do it. This is the pic of a Neon engine, your block is the same. Where we have the external cylinder head oiling line, you would put your sending unit. The "T" is just a water pipe "T" and you can get that at an hardware store, and the bushings to reduce the size if required.

Gary

Visit the Howell Automotive Open House August 20th, 2005. The largest gathering of Chrysler 2.0 engines on the planet.

US Small Business Administration Export Business of the Year for 2003

Visit Howell Automotive at www.howellautomotive.com

could I just pull out my window wash resivoir, and get at it from under the hood, rather than jack it up? the battery and everything has already been put in back...

____________________________
My $.02
95 GS

and where do I get the stainless braided hoses like that?

____________________________
My $.02
95 GS

You don't need that line. That doesn't have anything to do with the gauge you're adding.

http://www.cardomain.com/ride/3130861

why dont you just take off the factory oil pressure dummy sensor crap and screw in the sending unit for the oil pressure gauge? I didnt even get a CEL code...

>why dont you just take off the factory oil pressure dummy
>sensor crap and screw in the sending unit for the oil
>pressure gauge? I didnt even get a CEL code...

Leave both, because you will see the idiot light long before you notice the oil pressure gauge is reading "0"

Gary

Visit the Howell Automotive Open House August 20th, 2005. The largest gathering of Chrysler 2.0 engines on the planet.

US Small Business Administration Export Business of the Year for 2003

Visit Howell Automotive at www.howellautomotive.com

>could I just pull out my window wash resivoir, and get at it
>from under the hood, rather than jack it up? the battery
>and everything has already been put in back...

On the Neon you can get it from underneith, but on yours, I think you have the right idea.

Gary

Visit the Howell Automotive Open House August 20th, 2005. The largest gathering of Chrysler 2.0 engines on the planet.

US Small Business Administration Export Business of the Year for 2003

Visit Howell Automotive at www.howellautomotive.com

I did it from underneath... I don't think you could get at it from the top with the manifold in the way... I could be wrong, but soon I am switching the nylon line so I'll see what room is there from the top if you haven't allready done it.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.