I installed a ScanGauge II in my 97 RS today. Mounted it under my radio on a flat panel that was there. They're simple to hook up and do a whole lot of neat computations. I'm sure you all know. I bought it mainly for the scan tool feature and true to it's word it told me I had a 0442 code on my CEL.

Unfortunately though it won't CLEAR the code and turn off my CEL which is what I wanted the most out of it. Just thought I'd let everyone know in case you're considering getting one for that very reason.

I'll try to contact the manufacturer to see if they know how to overide the problem. Their manual makes it sound like if I got the dreaded blank screen after tring to clear it was more or less SOL.

Could just be my car or perhaps a 97 problem. Sure like to hear from someone that can actually use the Clear function.

I've had a Scangauge since they were first released and it has never failed to clear any codes (unless the problem still existed).

Are you sure you just aren't seeing the code reappear immediately after you attempt to clear it? I can't say I have specifically tried to clear a 0442 code but the only time mine has not cleared a code permanently was when I hadn't fixed the issue first.

Hi Dave. Thanks for the insight. No, I have not fixed the 442 code yet. It's a general EVAP code. All I know is when I push "Yes" to clear, the screen goes blank.

I contacted Linear Logic, the manufacturer, and they said I did the steps correctly. They also said the CLEAR function definitely works on all our cars.

They are sending me a new replacement unit and a prepaid envelope to return the one I have today. I'll reply here again and let you know if that did the trick.

How do you expect it to clear the code if it is not fixed?

It was my understanding it will reset (clear) the codes for a short time only. Like my evap problem. After it resets it takes x amount of miles to be smog ready. Hopefully you'll get the cert in that small window of time before the CEL comes back. Correct me if I'm spinning, lol, I do take alot of meds.

That's most excellent. Yeah, they treated me very pokitely and professional too.

Nemo, I have to thank you for showing this thing to me. I have never heard of it, but after reading about them you bet your ass Im going to be getting one. They look pretty bad ass. And they are actually cheaper than a code scanner you can buy at Autozone.

95 Eclipse GS: 10.5:1, Crower 2's and MSII
186 WHP - 150 WTQ
14.697 @ 93.85 MPH......Gone, but not forgotten
99 420A Avenger: Given to my sister
99 GS OZ: Sold
03 Evo 8: Family Car with balls

Yeah, they are pretty neat. Ebay has them all the time and the new ones all have the Xgauge software upgrade. I'm still trying to figure out all they do. It's not difficult; just alot. I've seen the used ones go for around $140 but I'd go new for $160 just because. I was fortunate to scoop a new one for $105 shipped from a private party but that was just dumb luck being in the right place at the right time. The people at Linear Logic, the manufacturer, are great too and provide personal type support. I'm sold.

Does it just stay stuck on a blank screen when you try to clear the code? Mine does that sometimes when the car is running, couple times when it was off with key in the on position. I'm fairly satisfied with the gauge. Update rates are very slow (even when it is set to fast). I wanted the aeroforce scangauge but its taking them forever and a day to come out with ISO format (Mitsu,Subi,toyota,etc). It only displays 2 gauges at once, but update rate is constant. For example, RPM on the gauge moves with the needle on the tach perfectly. Also does 1/4 mile times and now does HP i believe (more accurately than the scangauge 2. I called linear logic about the slow update rate, and they said it cant get any faster since the ecu only asks so many questions per second. 2 or 4 questions/sec. cant remember. But my laptop software is way faster even when i have 9 gauges put up on my laptop. I'll probably get rid of my scangauge and go with aeroforce if it ever comes out since it has enhanced interface options that aren't reported through general OBD2 such as knock (which is what i want)and it can record and add additional gauges such as wideband, egt, and more. Recording everything on one gauge will make tuning a breeze

That aerogauge sounds hot. I'll have to check it out.

Just got my new replacement ScanGauge in the late mail. Tomorow I'll stick it in and see if I can clear the code temorarily without fixing the problem;

And yes, when I tried to clear the code before, I always got the blank screen. I did it with the motor running each time but I'll try it with the motor off (never thought of that) before I do the swap.

Thanks

Ya, it seems it depends on the code whether it will clear it with the car running. Some i have cleared no problem with the car running, others dont seem to want to go away. If it just doesn't want to clear them altogether, then there's a problem.

I put the new unit on they sent me and it shows two codes now.
PO133 and PO442.

Neither one will clear with or without the motor running. I'll have to fix the problems first and try again.

The unit I have to return was probably just fine but it's nice to start out with something you know is new.

Sounds like you need a new cat too. Since code P0442 is cat converter efficiency failure

he might not need a new cat. His upstream o2 is bad, so it cant compare the downstream o2 to anything. Maybe that is why it is throwing the cat code...?

possibly. but the faulty o2 sensor causing too lean or too rich fuel mixtures could have ruined the cat

Ok, lol, that would be a blessing.

Can anyone elaborate more on that possibility?

Thanks Tyler & halfasss. (even though I'm confused I have hope)

Not to doubt you at all but can you be sure it's a cat efficency failure? The code book I have says just a vauge "evap" problem.

I've driven the car almost 2 months with that on because Aamco told me a PO442 was just a vapor hose. Terry said possibly a "roll over valve".

If you're sure it's the catalytic converter I could just bolt in a new one way cheaper than Aamco wants to fix a vapor hose.

Please double check that if it's not a big deal to do so and let me know. Thank you.

Thanks again, especially for the code definitions. I have a year to play with it before I *have to* (damn Ca. sucks) I'll definitely do the roll over valve and anything else I can find when I drop the tank. Rather spend a few xtra bucks and avoid double or triple labors.

just out of curiosity has anyone tried one of these in a 95? I like the idea but I don't want to spend money if it won't work

Erik P.
Official 2GNT thread Hijacker
Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be...
All we know is, He's not The Stig... But he is The Stig's Spartan cousin!

Pull up Linear Logic (the manufacturer)or just ScanGauge and write them. They're great people over there. Leave your phone # in an email and they'll call you within a business day.

Erik P.
Official 2GNT thread Hijacker
Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be...
All we know is, He's not The Stig... But he is The Stig's Spartan cousin!

I should have mentioned both of my 95 Eclipses are AWD in case there is a difference there.

I was told all 95s were OBDII compliant even though it was not mandatory until 96 model year.

Originally posted by RoninEclipse2G I was concerned because I have an extremely early build 95, Aug-94, one of the first 2gnt's built



Hoo hoo, I got you beat. My car, Date: MAY 1994.

I guess that may not be a good thing, since I want one of these and Im really hoping it works with my car.

95 Eclipse GS: 10.5:1, Crower 2's and MSII
186 WHP - 150 WTQ
14.697 @ 93.85 MPH......Gone, but not forgotten
99 420A Avenger: Given to my sister
99 GS OZ: Sold
03 Evo 8: Family Car with balls

---

2012 2500HD LML

I have one in my 95 Avenger and love it!!! I've had no issues clearing codes. I believe I have the vehicle with the motor not running when doing so.

Great investment.

95 Avenger 2.0 - Hahn 16g, DMS 8 injector setup, UDP, Big FMIC, HKS SSQV, MSD Coil & Wires,
ZEX Nitrous System, QTP Cut Out, Mandrel 2.5" Exhaust with cat delete, MP 60mm TB...and tons of Carbon Fiber

Once you correct the code, I always pull the - terminal to reset the ecu

97 GS Show Car
99 GST Daily Driver
99 Spyder

I just ordered one of these with my tax refund money. I was reading some comments about them elsewhere and I cant wait to get it. Hoping I can get the logger software somehow as well.

95 Eclipse GS: 10.5:1, Crower 2's and MSII
186 WHP - 150 WTQ
14.697 @ 93.85 MPH......Gone, but not forgotten
99 420A Avenger: Given to my sister
99 GS OZ: Sold
03 Evo 8: Family Car with balls

Im also eyeing one of these as well.

Or the Bluetooth OBD2 link. Adamzty has one, works great with the Palm, and I use Palm phones. Its a logger as well IIRC.

I was reading about some of the features this thing has. Apparently you can set it to read of the horsepower of your car. Any one have any idea how accurate that could be?

95 Eclipse GS: 10.5:1, Crower 2's and MSII
186 WHP - 150 WTQ
14.697 @ 93.85 MPH......Gone, but not forgotten
99 420A Avenger: Given to my sister
99 GS OZ: Sold
03 Evo 8: Family Car with balls

it's probably like the Gtech horsepower meters, a pretty simple calculation based on a small G sensor, the weight of the car and running a quarter mile. it's not dead nuts on but it'll get you in the right ballpark.

Erik P.
Official 2GNT thread Hijacker
Some say that he's driven over more Covenant than he's shot, and that his grenades aren't where you'd expect them to be...
All we know is, He's not The Stig... But he is The Stig's Spartan cousin!