i'm going in for my 60k and i think i have everything:

water pump
timing belt
tensioner pulley (i'm not gonna get the bracket)
udp (af/x)
fuel filter

i still dont have the camshaft oil seals... anyone know how much for this?

but are there any other seals or gaskets that are needed for the 60k maintenance?

btw up here in the bay area, the best prices i could find for labor are 300 in redwood city, 325 in menlo park, and 485 to 600 elsewhere, satan is around 800.

i dont know shit about the adjustable cam gears accept from what i've read on this board. it sounds like a good deal. modacar is selling them for $139, do i need two gears (one for intake and one for exhaust)? anyone know if its 139 for the set (if i do need 2 of them) or 139 each. is it worth it? for around a 5hp gain, it sounds like a deal especially for 139. and finally, since i'm going for the 60k maintenance thing, is this something that can be swapped out by the mechanic while they're in there.

*can i adjust the cam gears myself after they get installed or do they have to be adjusted at time of installation?


my car: gs, nt, at, mods:iceman cai, plugs and wires, gst exhaust, soon udp and maybe cam gears deppending on your feedback.

thanks.

mods:
gst exhaust, iceman intake, af/x udp, accell wires, ngk bkre511
soon: af/x tb

It is $139 per gear, and you will need two. If you’re going to do oil seals, I think you have to take the gears off to replace the oil seals, you might as well replace the stock gears with adjustable ones (assuming you want to spend the money on them). You can adjust the gears yourself, but most would recommend that when you do adjust them you do it on a dyno...so you can see the effects of the adjustments.



Eric Madden

www.howellautomotive.com has 5 bolt cam gears for $250 per set. 5 bolts on the gear is much more likely NOT to slip as compared to 3 bolt cam gears.

http://howell.mountain.net/Talon/DSMengine.html









current status unknown

http://hometown.aol.com/ohshootuhh/

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Drop in K&N Filter and open airbox
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

get sum vasoline for unexpected ass rapage...........

good luck

03 srt-4 13.130@112.47mph (n2o, stock turbo, 10/2003)
now: 20g, portfueler, bpu+++ (track/dyno times tbd...)

i farted on your wiki

I know it is better to adjust the cam gears with a dyno. But my question is can you adjust the cam gears without taking off the timeing belt? What is involved in adjusting the cam gears?

1999 Eclipse RS (all show)
1990 Turbo Eclipse (race)

To adjust the cam gears, you just loosen the three locking bolts, and turn the face of the gear. No, you don't need to take off the timing belt but you do need to leave the timing belt cover off so you can access them.

________________________________________

2004 WRX - WR Blue Pearl
1997 Eclipse GS - Royal Sapphire Pearl

i see, this answers a lot of questions. i guess i'll buy them and hold on to them till i get some crower cams and install all that once i save up some mo money. (planning on going turbo as well) i'm doing the whole, saving up a hundred here, fifty there thing, eventually i'll have enough. say in like 40 years or so, HA!

anyone know of any more seals and gaskets i'll need to replace for 60k?

ken

mods:
gst exhaust, iceman intake, af/x udp, accell wires, ngk bkre511
soon: af/x tb

You can get those exact cam gears at www.ptuning.com for only $104 a piece. Plus a 5% discount through the 2gnt site and free shipping. That comes out a lot cheaper the howell's price.

Ian | SoCal | Former 2GNT owner |
2GNT mods & pics: www.go.to/dsmdomination |
email: icjeclipse@earthlink.net |