From my understanding this motor is a "large 2.4L" (2429cc) and I've been wondering what the following bores will do in regards to increasing the overall displacement of the motor so I decided to do a little math. I even threw in some bore sizes for giggles.


stock bore = 2429cc = 2.4L = 145.7CI
.020 = 2xxxcc = 2.5L = 149.7CI
.030 = 2xxxcc = 2.5L = 150.6CI
.040 = 2xxxcc = 2.5L = 151.4CI
.060 = 2xxxcc = 2.5L = 153.2CI
.120 = 2xxxcc = 2.6L = 158.5CI
.140 = 2xxxcc = 2.6L = 160.3CI

I used the following sites for the calculations:
http://www.4lo.com/calc/literstocid.htm
http://www.21cgt.com/FMWebCatalog/frmConversion2.aspx

If I get "bored" (haha...) I might do the calculations for the 2.0 as well.

Feel free to discuss. This needs to be stickied!

How would the cylinder walls take to that kind of boring?

Red 97 Eclipse GS (420a) MTX
Custom Garrett T3 Turbo system
Megasquirt w/52 lb/hr injectors & a Walbro 255
Kicker/Alpine Audio (3 amps, 2 subs)
90 Cav 2.2 TBI auto (winter) <- yeah, it's fast

You would not be able to bore larger than .060. if you really wanted to do this you would need a "wet" sleeve to go that large. Then you would have to look into custom pistons and Headgasket might becoem an issue. He if your going to spend that kind of money you might as well o-ring the block if you arent reqd to.

The 2.6 is done as a stroker as well as overbore. This infomation is nice but i dont see how it should be stickied.

I will look into your other request though.

Terry

Bore is not the way to increase displacement, stroke is, and for that matter it's better to have a strong block and focus more on the technology that makes it go. There's an old saying, there's no replacement for displacement, but that came from a day when the only electronics on an engine had more to do with sensors and spark plugs than anything else. Be happy with the 2.4 as it is, if anything focus on getting the rotating mass down rather than the bore up. Do we not remember the hell that the reverand went through with his 2.6 attempt?

Representing the Central Cali chapter of 2GNT!
(I think I'm the only member )

2.6 attempt????? It wasnt an attempt it was a reality. That motor was running and on the dyno. Untuned it put out 306hp if I recall.Granted it was a real pain to create, it did come through in the end as was just sold to the third owner a month back.

i know this has been discussed far to many times but ill throw in my 2 cents anyway

anything under a .060 overbore is still less than 2500cc's, so its still a "large 2.4L". manufacturers round up, but the truth of it is that 1L = 1000cc's, so add it up.

cylinder walls might be a little thin but with the rate i rebuild engines anyway, it's fine. i went with the .060 myself, and i was more than happy with the low end torque.

_ _ _ _ _ _ _ _ _

96 Black ESi
91 Red TSI AWD (RIP)
02 WRX


"turnin wrenches for nine hours in the pouring rain, just to get the beast up and running again"

Aerospace Certified TIG welder for Precision Castparts in Portland, OR.

JoshSpair.com

All I remember about that thing was that it was a major PITA and it got sold because he was tired of it. Who bought it recently? What do they have it making? Still doesn't change my belief that boring metal out of the cylindar isn't the right way to increase displacement, but if I'm wrong about the reverends' 2.6 then I humbly retract my previous statment.

Representing the Central Cali chapter of 2GNT!
(I think I'm the only member )

Brynden sold the car to one of my friends in WI then he sold the motor so someone else because of some issues related to the car being broken into and the insurance/lawyer issues. The car was running and still in the preliminary tuning stages whn it put down 306hp. Search and you will find out who the owner was. The new owner I dont know.

Terry

Well apparently a few guys have punched the 2L out .140.

http://forums.neons.org/viewtopic.php?t=174134&highlight=bore

That post only proves how stupid of an idea this is and I would like to see where you count a "few" guys. I count 1 by that post unless you "see dead people". The guy who tried it stated the motor wouldnt hold bearings. Now tell me how this is a good idea when the 2.6 has been created with a stroke and a bore combination reliably. Not to mention you are still using the 2.0 stroke. How is this info a good idea?

Unless you show me measurements i will not believe boring a 2.0 that large. You should check out the 4g63 head conversion i have on my 420a.

My point is just because someone says they did it doesnt mean its factual. Show me the machining paperwork.

This thread is dead

Terry

I never made any claims of credibility.

I was just providing fuel for discussion and it looks as if I might've hit a nerve.

http://www.team-2g.com/mitsubishi-eclipse/showthread.php?t=5353&page=2
check the pic in the middle of the page

that was the neon sohc engine of a local friend of mine
bored I think 0.130 or was it 0.135 over and 13:1 pistons
the engine ran less than 2 minutes

he tried again with a second block , bored by a second machine shop and the newest engine ran for about 1000 miles before blowing

Alain

one of the 2.4 true pionners

dr1665 can you put the picture in a gallery and post it here ?

I'm at work right now and can't do anything from that pc

Alain

one of the 2.4 true pionners

How much is it bored in that pic?

I eat emo kids for breakfast

1995 Eagle Talon (SOLD)
72' SuperBeetle
72' Standard Beetle
56' Deluxe Beetle

Does the fire ring even function on that block? At least he can claim weight savings as one of the benefits

Representing the Central Cali chapter of 2GNT!
(I think I'm the only member )

What sort of self respecting machine shop actually did that?!?! Just tell the guy he's a moron and show him the door.

-"Easy Mac"
05 Mazda RX-8 (RR8 #88)
99 Eclipse RS 398whp & 372lb-ft

Those bores look HUGE but I think its just because, compared to the cylinder wall thats left, they are. That is probably the most surefire way to destroy a block I've ever seen.

1995 Eagle Talon ESi

Originally posted by DR1665

Originally posted by Blizare How much is it bored in that pic?

Originally posted by alain95i4 that was the neon sohc engine of a local friend of mine bored I think 0.130 or was it 0.135 over and 13:1 pistons the engine ran less than 2 minutes he tried again with a second block , bored by a second machine shop and the newest engine ran for about 1000 miles before blowing.

C'mon, man! You're slippin'!

I eat emo kids for breakfast

1995 Eagle Talon (SOLD)
72' SuperBeetle
72' Standard Beetle
56' Deluxe Beetle

Holy shit....did I type that?

I must've been drunk at work again.

I eat emo kids for breakfast

1995 Eagle Talon (SOLD)
72' SuperBeetle
72' Standard Beetle
56' Deluxe Beetle