ok guys.. dont yell at me.. but for about a year now i have had a nice amount of oil in my spark plug holes.. first it was just number 1..but now its all over them.. is that going to mess up anything or hinder performance or spark??

the guys that first told me bout it.. wanted 115 to do it.. glad i didnt pay them

since the kit is 13 bucks.. and my labor is freee and much more fun..

ahah

but i just was wondering??? maybe my car would be faster if i fixed it.. ahah prob not.. still be slow..

I love dino and 2gnt. ####ers (my word) bliz stole it but i let him borrow it

Nah. it's just four little rubber o-rings that go bad over time. It'll take you maybe 4-5 hours to do your first time. $115 is totally outrageous.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

holy shit, that takes 4 -5 hours i didnt put mine in yet but i dont want to spend that much time on it

Boca Raton, Florida
95 Eclipse GS- sold
99 Eclipse GSX- 386awhp
98 Eclipse GS- sold
92 Prelude

Shit 4-5 hours is nothing. Its all fun. You learn a lot.

Go put a turbo kit on

------------------------------------------------
98 ESi
95 GS

4-5 hours AT MOST! It only took me 1 - 2 hours for the VC gasket. Of course, after the cam install, I could get from running condition to vc off in 5 minutes!


current status unknown

http://hometown.aol.com/ohshootuhh/

Perf:
KYB AGX Struts
Neuspeed Sport Springs
5 Strut Bars (2 F/U, F/L, R/U, R/L)
Sprint Front Camber Kit
$15 Rear Camber Kit
Corbin's A/F Gauge
MSD DIS-2 Ignition System
Some Regrind Cams that need High Compression (which I don't have)
Ported Intake Manifold
Ported Throttle Body
Nameless Cold Air Intake with a K&N Filter
Custom 2 1/2 inch exhaust with Dual DTM Muffler
Empty Catalytic Convertor
Energy Suspension Motor Mount inserts
Hurricane_GS Short Shifter
Symborsky Shift Kit
Clutchmasters Stage 3 Modular
225/50/16inch Wheels and Tires


Audio:
Alpine CD Head Unit
Alpine Flex4 25W X 4 for Fronts and Rears
Alpine V-12 450W X 1 for Subs
Infinity Reference Series 5 1/4 and 1 inch tweeter component systems for fronts and rears
Blaupunkt 3 way 6x9's in the rears
3 MTX 5000 10" 12 ohm subs running 4 ohms mono

Flame Red SRT-4 GT40,8.5:1 Built Shortblock, Brian Crower Stage 2 Cams, etc etc etc...

Are you all on crack or something? 4-5 hrs to change a valve cover gasket set? on our cars? I just unbolted the coil packs, pulled the plug wires off, pulled the water temp wires off, unbolted the bolts on the valve cover with a deep socket, pulled the valve cover off, pulled off the old gasket, put on the new, torqued the valve cover to the specifications in the fsm, screwed the coil pack back on, and finished up... took maby 30-40 min i guess 1st time.. am i missing something? or did you all take advantage of having the cover off and clean the valvetrain? Thats probably what i shoulda done, but I'll open the can of worms when it gets warm out again... yah know?

man u guys suck.. ahah jk...


u totally didnt answer the question can u re read it..

i want to know if the oil in there is messsing anything up.. or hurting performance..

i dont care how long it takes. grrrrrrrr

I love dino and 2gnt. ####ers (my word) bliz stole it but i let him borrow it

oil in spark plugs + less spark = loss of performance.

I'd change it.


admin@dsmscene.com
To all da haterz: _|_ tia
"Anything in parenthesis can (not) be ignored."

if it seeps in you could mess up the wires / spark plugs. So just check them when you do the valve cover gasket, and yes this can hurt performance if the plugs/wires are bad.

"The fastest draw is when the sword never leaves the scabbard,
The strongest way to block, is never to provoke a blow,
And the cleanest cut is the one withheld."

Michael J. Kulaga
e-mail: Michael_97RS@2gntDSM.zzn.com aol IM: MJKulga
http://highlander.dsmpower.com/

All Motor Beast in the Making

Injen CAI, 55mm TB, Hooker 4-1 Stepped Header, GS-T Muffler, AFX UDP, S-AFC, 8.5mm Magnecor Wires, SS Clutch Line, NRG Susp. Motor Mount Ins., FU/RU/RL STBs, TSW Blade 17x7.5, Bridgestone Potenza RE730 215/45ZR-17. Front KVR Cross-Drilled Rotors and Carbon Fiber Pads

To Be Installed: Ported/Polished Intake Manifold, Rear disc brake conversion kit, SS Brake Lines, Rear KVR Cross Drilled Rotors and KVR Carbon Fiber Kevlar Pads

Firefly:
Mal: You don't know me, son, so let me put this to you plainly: If I ever kill you, you'll be awake. You'll be facing me. And you'll be armed.