Welcome to the 2GNT Forum!
Home Site Background Info & Specs Mods & Tech Info CAPS Part Reviews Donate 2GNT Stickers
Search Printer-friendly copy 2 Users in Chat
Top 2GNT Technical Performance/Engine Manual Trans - NV-T350 topic #3844
View in linear mode

Subject: "i think my clutch is finally done...." Previous topic | Next topic
talonguy2005Jan-04-05 04:02 AM
Member since May 16th 2004
1473 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3844, "i think my clutch is finally done...."




          

well, i started my car this morning, and let it warm up for a little bit. Then I went to go put it into reverse to back out, and it would not go into gear. It wouldn't go into any gear!!! Then i finally got it to go into reverse, but it grinded a little bit, but i didn't even let the clutch out and it was already moving by itself, wtf!?! the clutch is engaging before i even let the pedal out at all what is going on here?!



1992 Plymouth Laser
-Bone stock for now.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Replies to this topic
RE: i think my clutch is finally done...., Global Ruler Of All ThingsDarkOne, Jan-04-05 05:24 AM, #1
RE: i think my clutch is finally done...., talonguy2005, Jan-04-05 06:42 AM, #2
      RE: i think my clutch is finally done...., talonguy2005, Jan-04-05 08:09 AM, #3
           RE: i think my clutch is finally done...., ajcfalcon, Jan-04-05 08:27 AM, #4
                RE: i think my clutch is finally done...., Global Ruler Of All ThingsDarkOne, Jan-04-05 08:59 AM, #5
                     RE: i think my clutch is finally done...., talonguy2005, Jan-04-05 10:45 AM, #6

Global Ruler Of All ThingsDarkOneJan-04-05 05:24 AM
Donating 2GNT member
14955 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3847, "RE: i think my clutch is finally done...."
In response to Reply # 0




          

Check the clutch fluid reserviour, check the slave cylinder for leaks, check the master cylinder for leaks.

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

    
talonguy2005Jan-04-05 06:42 AM
Member since May 16th 2004
1473 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3849, "RE: i think my clutch is finally done...."
In response to Reply # 1




          

the clutch fluid resivor was completely empty emoji i added some fluid in, but it still isn't fixed at all. Now i have almost no pedal pressure. Also i cannot find out where it is leaking from.



1992 Plymouth Laser
-Bone stock for now.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

        
talonguy2005Jan-04-05 08:09 AM
Member since May 16th 2004
1473 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3850, "RE: i think my clutch is finally done...."
In response to Reply # 2




          

ok, i just checked, and the area under my dash was covered in fluid, and the clutch master cylinder, and i called an they are like $89 for a new one from autozone. does that seem about right?



1992 Plymouth Laser
-Bone stock for now.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

            
ajcfalconJan-04-05 08:27 AM
Member since Nov 22nd 2003
1104 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3851, "RE: i think my clutch is finally done...."
In response to Reply # 3


          

you can rebuild the master cylinder for about $15 from napa online. I havnt done it yet, but im getting ready to do it and i hear its pretty simple.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

                
Global Ruler Of All ThingsDarkOneJan-04-05 08:59 AM
Donating 2GNT member
14955 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3852, "RE: i think my clutch is finally done...."
In response to Reply # 4




          

I'd just buy a new one, personally. I think I paid a bit more for the last one i bought.. $90-100 if i remember right.

The master cylinder is pretty easy to replace, too. Just in a tight spot...

You got off easy emoji

______________________________
If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.

'95 Eclipse TurboGS (garage deco)
'95 TSi AWD (restoring a survivor)
'97 Talon ESi-T (poor impulse control)
'99 Eclipse RS-T (daily beater)
'13 Evo X (mostly stock)
'17 Sienna (Middle Aged Dad Mobile)



Factory Service Manuals: http://nawdu.de/files/

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

                    
talonguy2005Jan-04-05 10:45 AM
Member since May 16th 2004
1473 posts,
Click to send email to this author Click to send private message to this author Click to view this author's profile Click to add this author to your buddy list
#3854, "RE: i think my clutch is finally done...."
In response to Reply # 5




          

i ordered one from autozone for $102 shipped, because no one carries them!!! not even the dealership. hopefully that is all that needs replaced emoji there wasn't one drip under my car this morning, so im guessing it is the master cylinder



1992 Plymouth Laser
-Bone stock for now.

  

Report This Post to Admin Printer-friendly copy | Reply | Reply with quote | Top

Top 2GNT Technical Performance/Engine Manual Trans - NV-T350 topic #3844 Previous topic | Next topic
Powered by DCForum+ Version 2.2
Copyright 1997-2005 DCScripts.com, Copyright 2005-2026 2gnt.com
Generated in 0.027 seconds, executing 28 queries.