I have to move soon, so all the rest of my stuff has to go. Located in 15146, but obviously i can ship everything.

I have a 1998 gray auto gs that runs and drives. It doesn't pass PA inspection because of the rust hole in the strut tower, and some of the wheel bearings are getting bad. I'm not wasting any money fixing it. It has a rebuilt engine (30k ago), new headgasket doesn't leak (head machined), all new timing parts, etc, when i put it in. Auto trans runs fine, has newer pan/seal, doesn't leak at all. Car has dead battery right now from sitting. The only damage to it is the front left corner where i rubbed a median one time and it damaged the front bumper, hood a little, scratched the headlight, and dented the fender, so those parts are bad.

The rest of the car is fine. Has all power options and a sunroof from the south that doesn't leak and is in great shape. Some junkyard will give me $300 to tow it away and not deal with the aggravation of it ever again. It's not worth welding a new strut tower in. So, if people want to make offers on parts they need, if enough of you have interest and its worth it to me, i will part it out and get everything on its way. If you offer $50 for an engine, the whole deal is going to the scrap yard, so make reasonable offers.

I also have a 1995 sebring lx with a 420a and manual trans - ie, it's an eclipse with a trunk. I took the motor out cause the head was junk, bad timing belt. The car, however, is very solid. Almost no rust cause it sat in my garage for 5 or so years. Very good shape for a 95. Let me know if you need any part off it, cause its going to the scrap yard for sure. I was going to take its strut tower and put it in the eclipse, but time has expired on these.

PM me or post here what you need and what you're offering.

Thanks in advance.

Oh, and yes, everything is stock. I have some performance parts laying around here somewhere, but that would be a separate list. And the stock exhaust is relatively new and in good shape btw.

What I color interior?

Grey cloth.

PM'd

How about the center console prices from the eclipse (excluding shifter and bezel)
Factory Side skirts?

Originally posted by venge24
How about the center console prices from the eclipse (excluding shifter and bezel) Factory Side skirts?

Yes i have the center console, how much are you offering shipped?

I have all the side skirts except for the drivers fender piece. Again, how much are you offering shipped?

I should have said, i'm only shipping to the 50 states. I don't have the time or patience to deal with foreign countries right now. Been stuck with too many unpaid customs bills. Unless you make an offer i can't refuse that covers $50 in customs just in case.

Oh, and all this stuff that never sold, it's all just sitting here in boxes still - if you don't like the prices, THEN MAKE OFFERS:

used inline fuel pump that came with a hahn kit, probably a walbro or accel...comes with bracket and some hose...
$75 shipped

stock fuel pump bracket that fits into tank, great condition
$20 shipped

used autometer pro comp ultra lite electric oil temp gauge #4356
$150 shipped

used autometer sport comp AFR gauge
$55 shipped

used autometer pro comp ultralite electric fuel pressure gauge, 100psi #4363
$185 shipped

DOHC exhaust flange - mild steel, cnc'd
$50 shipped

used professionally ported TB, 55mm
$100 shipped

new PS pump pulley, plastic, 4 grooves like a neon, 04668448aa
$15 shipped

new 2.4L PT cruiser front timing cover, 04884409aa
$15 shipped

several sets used stock injectors
$30 shipped each

new aluminum upper rad hose replacement - actually fully aluminum, not braided rubber, summit sum-390124, 24" long with ends
$70 shipped

new sealed power bronze valve guides
$30 shipped

new turbo xs type h blow off valve - not "rfl" type
$130 shipped

used 4an hahn turbo oil feed setup
$50 shipped

used autometer pro comp ultralite electric EGT gauge and probe 1600F #4344
$120 shipped

like new autometer carbon fiber ultralite 30psi electric boost gauge, only gauge was hooked up, rest is unused including electronic boost sensor #4777
$165 shipped

new greddy full auto turbo timer - with eclipse harness
$80 shipped

new pt cruiser rockers - set in a head that was never run
$130 shipped

new "fuel line setup" - i have 6ft 6an braided, 10ft 8an braided, and many, many, fittings that i had ready to make a who new fuel setup for my car, front the pump output to a FPR through 2 fuel rails, its all there
$140 SHIPPED for fuel parts - TELL ME WHAT YOU NEED - 8AN SETUP READY TO GO - also have turbo water cooling lines, oil lines, etc.

new 5269558 sensor - genuine mopar oil pressure sending unit
$70 shipped

new 33004281 sensor - genuine mopar coolant temp sensor for 95
$30 shipped

used weld racing wheels, a pair for front, 15" x 8", 4.5" backspace, i believe called "rodlites", they have dual 5 bolt patters, so they fit other cars too...
$400 shipped

used fluidyne radiator
$300 shipped

2 used low profile pusher fans for fluidyne
$120 shipped

new magnaflow mp 7010 inline fuel filter - 25 mictors, 8an inlet/outlet
$80 shipped

new 2.4L oil pump
$130 shipped

stainless tubular turbo manifold - i bought all the parts, cut them all on the horizontal bandsaw, got everything ready to get welded...and never got it welded...comes with everything seen in this post, you weld it yourself or get someone to do it...will fit an "s cover turbo" on a 2.4L swap...
http://forums.2gnt.com/dcboard.php?az=show_topic&forum=8&topic_id=100980&mode=full
$200 shipped

new 2.4L crank scraper plus new oil pan gasket
$70 shipped

new arp exhaust manifold studs - 4 in package, 4 only used to mock up manifold...
$60 shipped

new mopar 05269983 genuiune mopar map sensor
$80 shipped

new mopar 33004280 genuine mopar air intake temp sensor
$25 shipped

used 4671276 mopar map sensor
$30 shipped

strut tower bar front
$25 shipped

new 3 gauge pillar pod, grey
$20 shipped

brand new 2.4L timing parts - all genuine mopar parts - also have brand new mopar timing belt to go with them - includes both bearings and the hydraulic tensioner
$180 shipped

two titanium bolts i had made to hold the hydraulic pin tensioner in
$20 shipped

perfectly sized block to use a hyraulic pin tensioner on 2.4L block - if you need this, you'll understand where it goes - between block and hydraulic tensioner on a 2.4L
$20 shipped

new rear timing cover for 2.4L block
$25 shipped

another new front timing cover for 2.4L block, partially modified to allow us to use our passenger side mount
$25 shipped

PICTURES OF THIS STUFF HERE:

http://forums.2gnt.com/dcboard.php?az=show_topic&forum=16&topic_id=116029&mode=full

I have my stuff shipped to Maine and cross it myself