is there a post or a write up on installing an EGT? ive been turbo about 8 months or so now with no issues but for safty purposes id like to go ahead and install one? i know its as simple as running a power wire and connecting a probe into your manifold but i wasent sure if theres a way to do it without drilling a hole in your manifold? probably a stupid question but is this something i want to attempt myself or should i get it done somewhere? i know you wanna tap the probe in the #1 runner about an inch or so away from the head? is that all there is to it? any help would be greatly appreciated, and if theres a way to do this without taking all my stuff apart again that would be nice too
thanks in advance
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

There will be arguments on where to tap but I like the number 1 or 4 runner. I have heard good arguments for both. Some people will tell you to install in your dp too. My friend has his in the dp or his srt4 and the temps are way lower then mine. Like 600 degrees goint dow the road. I would tap a runner.

As far as a write up there Is one on tuners but the site is down right now so I cant post a link. Just make sure to get all the little pieces out of your mani after you tap it. Good luck

Thanks, yeah i been reading for the past few hours on it and i think im just gonna tap the #4 for 2 reasons really, 1 being it seems to be the popular demand and 2 being i want to tap it out to the side and if i do that at number 1 im gonna hit the dp or be awfully close to it. also sorry again but i never had to tap anything before, will it require welding or is it just as simple as tapping a hole threading it and screwing the probe in??

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

is it just as simple as tapping a hole threading it and screwing the probe in??
yup its that easy

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

In fact they make tap and die (spelling?) kits out there that you can probably pick up at a local hardware store. Those usually come with everything you need except for a drill.

I contributed to the wiki!

95 Eagle Talon ESi-T (BACK FROM THE DEAD!)
98 Dodge Neon R/T
93 Saab 900 Turbo Commemorative Editon #86 of 325 (sold)
95 Volkswagen GTI VR6 (saved from crusher)(sold)

I drilled mine, then took it to get it welded to insure a proper seal.

New Car:
2004 350z base, Nismo CAI, pioneer avic-n1 (dvd, cd, navi)



Old Car:
1998 GS with hrc stage 2, HID 6000k conversion kit, AEM UEGO wideband, sfmu, ml, prokits, Greddy warning gauges: egt, boost gauge, and oil pressure, apexi tt, haydans tranny cooler, costum dp, groundwires, dynotune fp gauge. gst muff, turbo spoiler
Boostin since Aug 03.

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!

i believe i might be doing the same thing, always nice to be safe than sorry later

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

If you dont want to take the manifold off while you are drilling and tapping have the engine idling so the metal chips will be blown out the hole instead of through laying in the manifold to be sent through the turbine.

I actually ended up tapping between 3 ad 4 because on the hahn manifold that is where a good flat spot is and it didnt interfere with the elbow coming off of the turbo. To seal it up I used this liquid manifold weld stuff that supposedly gets stronger as it gets heated up. 2 years and no leaks yet so it seems to work.

1996 eclipse GS-T
1968 Ford Mustang
2004 Suzuki GSXR600
2006 Honda CBR1000RR
Decisions Decisions

I just used JB weld and its held up fine

I contributed to the Wiki!
EVO IX - just a really expensive boost gauge and a K&N air filter
96 Eclipse RS -awaiting registration and inspection
95 Eclipse GS - parts car
Mods/Profile - http://www.2gnt.com/index.php?d=cs82685

well its finally in, it was as easy as pulling the manifold drilling and tapping like everyone said. I Decided to go against the grain and tap runner #1 i think it looks better there, anyway got it all hooked up and running and at idle im seeing around 900 and cruzing it goes to about 1000-1200, but if i get on it the temp really climbs from 1000-1400+ quickly. wow i see now why it is important to have this gauge, while under full throttle my a/f gauge is pegged green but my egt's climb quickly to 1400 and will go higher if i allow it. im sure i can find it if i searched but quick question what is a safe temp to let go at? i been dropping off at 1400 but i think i can go higher
thanks in advance
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

everything that i have read has put 1600ish as the mark to let go of the gas on

1996 eclipse GS-T
1968 Ford Mustang
2004 Suzuki GSXR600
2006 Honda CBR1000RR
Decisions Decisions

I eat emo kids for breakfast

1995 Eagle Talon (SOLD)
72' SuperBeetle
72' Standard Beetle
56' Deluxe Beetle

i thought so too with the stock injectors however what would explain my black plugs? and i mean black as coal???

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

Even though you already have it in I would still like to post a link to this thread on sovadsm about installing an EGT probe.

http://www.sovadsm.com/forum/viewtopic.php?t=132

Maybe this could be added to the main page write-ups?

_____________________________________


http://www.dsmregistry.com/detail.php?carid=1133
*form follows function*

my egts rise real quick . im runnin 30lb injectors . at idle it at 900 . cruisibg around 1200-1300 and at full boost(6psi) gos to 1450 and rises to 1600 in about 10 seconds . when i had stock injectors at full boost it would always be at 1600

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

wow these temperatures seem high, i mean 1400 degrees is hot enough to weld with much less 1600. so basically what everyone is saying is its perfectly normal to have egt's of well into the 1400 degree range cause i always thought the lower the temp the better off you are. what about if i get a s-afc and tune it to run around 1000 all the time is this possible? or am i way off here? i will be upgrading to 30# injectors soon but until than im just trying to get a feel for this egt. thanks for everyones input though its really been a big help.
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

Took it for its 1st real drive today and egt stay aroung 1400 while driving down highway at 80mph and sit around 1000 while driving around 30 mph. while boostin they go as high as 1550. it just feels weird driving down the road with a steady 1400 egt reading, guess its always been that way and i dint know it until i put the gauge in. Car runs excellent.
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed