I need to build a oil line setup for my 14b. From http://www.turbosupply.shoppingcartsplus.com/page/page/1027453.htm
what parts do I need. Im not lazy, I've been searching the forums for a while and gathered much information, but cant piece it all together to understand exactly what I need. I hope that I can gather these parts or at least most of them at local hardware stores or FleetFarm/Menards/HomeDepot.

I just dont know exactly what adapters and sizes of them to make it work. Also where can I get the red/blue colored adapters and where are the placed in the setup? Thanks, any info greatly appreciated as always!

this site may help you out . you can get the npt fittings from home depot and the an fittings from places like ebay or anplumbing.com and such .
http://dsmtuners.com/forums/showthread.php?p=1509962#post1509962

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

What part actually plugs into the turbo cartridge? Which fitting? Also, the anplumbing website doesnt work or something, or at least I cant get to it. What other websites like that are there?

hummm all said and done I am pretty sure this is what I had in the order it went from the sender to the turbo:
3/8" NPT -> 1/4" flare fitting
-4AN fitting
-4AN SS line (48" is what I have, you could get away with a 36" I believe, maybe even smaller since my line is wayyy too long)
-4AN -> 1/4" NPT fitting
and the last 1/4" fitting just went straight into the turbo. Note that I do not have my stock oil pressure sender anymore, so you will need to figure out a T on your own. I never actually installed my 14B though, so I cannot say for sure if the 1/4" NPT is the right size. I used a T3/T4 instead and it did use the 1/4" NPT into a banjo bolt.

1995 Eagle Talon ESi

Wonderful thank you very much, one more thing, any pics of yours or one very similar?

i believe i used 4an to 1/4''npt to the turbo .

http://imageshack.us>

http://imageshack.us>

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

So where did you get all this stuff without spending a ton of money? All of the Russell Performance ends are fittings are like at least $20 a piece. I would like the red/blue anodized pieces. Where can I just get ss braided lines without any ends on them. Autozone/Checker/Advanceauto doesnt have anything but fuel kits with ss lines in them. Home Depot has lines but they have a rubber inside so that wouldnt work right? Bear with me on all these questions, I really appreciate it though!

Edit: Where can all the Earl's Plumbing parts be bought at?

Your 14B uses a banjo style bolt with 2 copper washers one either side of it for the feed. You can get a stainlesss line from rre but i dont think it nearly long enough, I'm sure you can get them to make you a longer one or at the least get you the fitting that goes on the end. I can't remember what I used when I had the 14B on my car. Anyway hope this helps. http://www.roadraceengineering.com/2g16ginstallkit.htm

about 1/2 way down this read there is a nice pic of the feed line.

http://vfaq.com/mods/2G-16G.html

Kevin
The old:


The new:

http://www.mainsitepage.conceptillusions.com/Turbo%20Kits%20Page/Oil%20Lines%20Main%20Page/OIL%20LINE%20KIT/index.htm

$50 oil feed kit made specifically for the 420A (includes T) with whatever fitting you specify... can't really beat the price.

please do not turn this thread into another CI debate.

-marc

the cheapest place for ss line and fittings is ebay . i bought mine at a performance shop for like triple the price it is on ebay .this is all you need right here in an fittings and line . cant beat that price

http://cgi.ebay.com/ebaymotors/Steel-Braided-Brake-Line-4AN-x-36-w-90-degree-NEW_W0QQcmdZViewItemQQcategoryZ33562QQitemZ8010090324QQrdZ1QQsspagenameZWDVW

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

I paid the money for all Russell Performance fittings. They just look too damn good to not use. $20 a pop? You are getting jipped, mine I think ranged from $5-$20 (and the $20 ones were -10AN).

1995 Eagle Talon ESi

Alright, with the line squared away...what do the fittings, flares, npt etc. This...
#90871, "RE: Oil Line instructions?"
In response to Reply # 2
Oct-25-05 06:20 PM by BumpinTalon

3/8" NPT -> 1/4" flare fitting
-4AN fitting
-4AN SS line (48" is what I have, you could get away with a 36" I believe, maybe even smaller since my line is wayyy too long)
-4AN -> 1/4" NPT fitting
and the last 1/4" fitting just went straight into the turbo. NPT is the right size. I used a T3/T4 instead and it did use the 1/4" NPT into a banjo bolt.

Now I need to match these descriptions with pictures because obviously I havent done this before, sorry, and I dont know what each looks like. Thanks all who have and keep on contributing!

1995 Eagle Talon ESi

Sounds great, thanks for being patient!

Well the 14b does use a banjo fitting and the tread size is 12mm x 1.25. What I did was take a old banjo bolt and cut it off and then weld a -3AN to it. (I cut the bottom of a -3AN to-3AN off). Now this works well but since it is so small it will have to be tig welded. As for out of the block its 3/8 NPT at the oil pressure sender. So simply take a 3/8 NPT nipple and put that into a brass 3/8 NPT Tee and tread your oil pressure sender in one side and then use a 3/8 NPT to -AN adapter. (I had to use a 3/8NPT to -4AN and then a Female -4AN to male -3AN for the supply line.) Hope this helps, let me know if you have any questions about a 14b setup.

I know it sounds cocky, but dont worry its not. Like I said before, pics really help at this point because I havent done this before so I dont know exactly what the different fittings look like. I look all over online, but there are so many different names it seems so if you or bumpintalon or anyone else have pics of what they are, that would be best for now. Thanks

i could post them up her but i dont have anyway to host them or i could email them to you let me know.

Sure, if anybody has some info, good links, or pictures of the fittings, flares, npt, send them to clipsetunr@hotmail.com. When they describe the fitting with a say -4an, what end of the item is it? I take it that that side is the one that the line goes into, but how does it stay in there without coming out? Im really starting to think that this is a lot less complicated than I first thought. Like I said, pics are the best right now so I think that will lead me in the right track for sure! Thanks

.........................................................................................................................

Built. That's All...
.........................................................................................................................
www.monkeybuttpirate.com
.........................................................................................................................
2 Fingers of Scotch with a milk back... Stat!

Thanks, I didnt see that on the website.

When you put an Earl's econ-o-fit hose clamp on the end of a line, how do you connect anything to that hose clamp. There arent any threads on the inside or outside so how do they work? Do you put both the hose and the fitting inside the hose clamp?