I saw this on ebay and bought it. Check it out and let me know what you think.

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7914790571&category=36474

i outa bitch slap you till the cows come home....

its obx...do a search!

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

Actualy my friend ...its nice decoration..you will see hp losses

vote for your choice of body style for Bluie!! http://www.cardomain.com/id/bluemooneclipse

www.Fastfabrications.com makes a sheet metal intake for our cars and it does help with power. but its only the top portion so u will still need to port out ur bottom runners pics below the design on the new ones r a little differnt.



je pistons, je rings, eagle rods, srt4 headgasket, crane 16's, crane valve springs, aem cam gears, 2.4 udp, fast fabrication sheetmetal intake, 70mm Tb, p&p runners with 8 injector setup, 450's and 550's, fast Fab turbo manifold, 38mm Tial waste gate, T3/t4, spearco 32.5x8x3 fmic, 2.4 pt tranny, solid front and rear motor mounts, quaife lsd, spec stage 4 clutch, custom ground kit, crane ignition etc. sonn to have smt6 tuned at 20psi

also 95 silver gs has one for sale in the for sale section

je pistons, je rings, eagle rods, srt4 headgasket, crane 16's, crane valve springs, aem cam gears, 2.4 udp, fast fabrication sheetmetal intake, 70mm Tb, p&p runners with 8 injector setup, 450's and 550's, fast Fab turbo manifold, 38mm Tial waste gate, T3/t4, spearco 32.5x8x3 fmic, 2.4 pt tranny, solid front and rear motor mounts, quaife lsd, spec stage 4 clutch, custom ground kit, crane ignition etc. sonn to have smt6 tuned at 20psi

that is the ugliest POS intake ive ever seen.

and do you have any proof that it does more than just deliver air like our stock one?

USED TO HAVE...Everything you wish you had, and then some...

You are somebody special Tim, you matter! - from the admins (but nobody likes you, because your username is just like that other guy's, and you whine a lot)

Originally posted by Initial DSM

Originally posted by siueclipse and do you have any proof that it does more than just deliver air like our stock one?

Gimme some time, I need to dyno it. Prolly about as long as its gonna take you to post your dyno sheet.

www.gregsorrells.com

http://ubanimator.com>

ok i was going to dyno it but i have a 70mm mustang tb on that intake and it wont work on my stock manifoldso numbers from my car wouldnt really show it gains. would be nice though i'm going to get tuned at 28psi with a small shot of nitrous down low to make the turbo spool. the turbo is a custom T-54 turbo built by precision turbo which surports over 600 something hp and fuel system with be the smt-6 with 8 injector setup should do good just need to finish my headwork so i can take it up to turbo tune and let mark work his magic

also this intake was on my friends rst till he blew a headgasket and it made a world of difference

Good luck w/ traction. Keeping the tires on the ground w/ my .50 trim is hard enough w/o spray. A t54 on a 2 liter is overkill imo but everyone likes big turbos. I wish you luck, keep up posted on those dyno numbers.

400whp or bust.

yeah traction is going to be a major issue but turbo lag will work to my side a little bit till i can fully upgrade my suspenion i have been looking at wheelie bars like on smithelys gst and have sent him some emails with a few questions about them and i've got some drag launch springs orderd plus slicks and a quaife lsd so hopefully i'll will be able to get some. u really dont build much boost off the line anyways when ur on the studder box my friend is running this turbo on his neon and he only builds about 10psi off the line.