Never had the problem until I boosted. Car runs like crap but im thinking a bad ignition coil. What causes a CEL 13? Any possible fixes.

I wish you a smooth break-in and happy driving.

Mod lists here:
http://www.dsmregistry.com/detail.php?carid=1065

No the ML should no cause a cel. If it was failing to prevent fuel cut, then the cel should be 109, I think for manifold pressure, not sure though. What's cel 13?



-------jezreel
hrc stage 1, sfmu, ml, prokits, egt, boost gauge, apexi tt, haydans tranny cooler, costum dp, dynotune fp gauge. gst muff, turbo spoiler

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting

CEL 13 - No change in MAP from start to run

---------------------------------------

---------------------------------------
-Ian
---------------------------------------
-1996 Mitsubishi Eclipse GS (SOLD!)
-2006 Nissan Frontier NISMO
-2003 CBR600RR
---------------------------------------

Could be a faulty ML. sounds like its blocking the MAP entirely, instead of just when boosting.


1997 Silver RS
Wiseco 8.8:1 Pistons(back to low compression!)
Eagle Rods
T3/T4 Turbo
Custom FMIC
Greddy Exhaust
390's
Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)

It's possible that the ML is stuck shut. You could isolate the ML from the MAP sensor by removing the ML, reset the ecu, and then take it for a short run to see if it'll throw the same code (just an idea.) If the problem persist w/o the ML, then the MAP sensor is probably bad, or vice versa.

___________
Kon C

"Sometimes, a man has to do what a man has to do."

Actually I got this code on the way home from jamesman's place.

At around 2500 rpm at 45 MPH on the freeway on-ramp, the car bucked, and picked itself back up again. On the drive home, i didn't boost it.

after I got home, I key danced and got 12-14-55. MAP sensor voltage too low/high.

Pulled my ML and clean the mofo out. Will go for a drive tomorrow to see if it comes back.

-K-

Dammit, gave wrong advice.

-------jezreel
hrc stage 1, sfmu, ml, prokits, egt, boost gauge, apexi tt, haydans tranny cooler, costum dp, dynotune fp gauge. gst muff, turbo spoiler

nothing like driving with the windows down and the music low: i love hearing the turbo spool, swwwhhhttt!!!!
thanks for www.kaptainmyke.com for the sig hosting

Is the MAP plugged in all the way?

Did you take the red shipping plug out of the ML before you installed it?

Take the ML off and see if you can blow thru it one way. If not, it needs to be cleaned. Dip it in some acetone or blow some carb cleaner through it.

I think i read somewhere that you can blow air through the missing link one way but if you flip it and blow air through it, the air wont pass through. Is that right? Or am I suppose to be able to blow through it really slightly but if i put a lot air through it it'll close. I guess what I'm trying to say is, how does the Missing Link work? And how do I find out if my Missink Link is faulty?

I wish you a smooth break-in and happy driving.

Mod lists here:
http://www.dsmregistry.com/detail.php?carid=1065

You should be able to suck through the bottom, but not blow through. Go give it a suck! Mabye you installed it wrong?

____________________________________________________
four nails four corners four riders and four horses

This thread has just gotten out of hand.


1997 Silver RS
Wiseco 8.8:1 Pistons(back to low compression!)
Eagle Rods
T3/T4 Turbo
Custom FMIC
Greddy Exhaust
390's
Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)

Originally posted by Nitrous_RS1997
This thread has just gotten out of hand. 1997 Silver RS Wiseco 8.8:1 Pistons(back to low compression!) Eagle Rods T3/T4 Turbo Custom FMIC Greddy Exhaust 390's Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)

____________________________________________________
four nails four corners four riders and four horses