#62380, "What next? #14 turbo cams vs cam gears vs afx udp"
I am running 7 psi and want to know on any suggestions on what next to get, i am rebuilding within the next two months so the bottom end will get done, but i need something now. I would like top end power, but i know there are other turbo 2gnt'ers that know more about everything and could give give me good suggestions on all of them whether top end or bottom end(AFX pulley).
99 RS-T "New bottom end(8.6:1 w/long rods)" Turbonetics 60-1/Portfueler/etc!!!!!
#62382, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 0
forget a udp for right now, cams hands down.
DWAYNE H 1996 eclipse under construction widebody eclipse, targa top, 19inch rollers, big brakes, 10 point custom cage, frank 2.4 hrc s20g turbo, custom marble paint job
#62384, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 2
i have to agree wit the cams but for a diff. reason, the udp would be so much easier to install when the engine is out for rebuild since u can just set it right infront of u and go to town
Mods: CAI, OBX exhaust, Grillcraft grills, altezzas, ard ryver g6 17's wrapped w/ falken's, VIS racing c.f hood, 2 12" kicker comp's w/pioneer h.u, streetglow blue undercars, red dash kit, indiglo guages, n other shit
#62387, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 3
you'll probably end up wanting something more aggressive than the crane #0014's at some point down the road like crower stage 3's or the crane #0018's. from what i've learned with my car, do things once by buying the best the first time, and then install and tune it right. i'd reccomend the AF/X UDP for now, then save up to completely upgrade anything and everything that moves (and some stuff that doesn't move) in the top end.
#62400, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 4
Thanks for tne suggestions, i think i am going to get the cam gears and afx pulley that way i can get the cams installed when i get the motor taken out for my rebuild.
99 RS-T "New bottom end(8.6:1 w/long rods)" Turbonetics 60-1/Portfueler/etc!!!!!
#62414, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 6
Originally posted by esseclipse I have the #14 cams but I have not installed them yet. Why do you say they are not aggresive enough? They are for turbo cars right?
I don't think NER kept in mind that he will be turbo, the 14's are best for turbo.
If possible the #14 shoud be on hand when the motor is rebuilt(logicaly) if you aren't doing it right now then I'd just say wait for until you're near install to get them and opt for the gears and UDP right now
*Skrilla "Honest officer, I thought you were trying to race me" Talon: 1st 2.4L '97 Prelude '04 350Z
Originally posted by YourInMyMirror95GS dick teaser's should be rounded up and shot in the forehead
Originally posted by etx Good luck man! Project 'STFU Brian your talon is dead meat' should be on it's feet soon!
Originally posted by Dark0ne Thanks. Now excuse me while i fuck your sister.
#62501, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 7
sorry to steal this thread but, What cames work best on a turbo auto trans that revs only to 6500. I'm mainly looking for torque across the board not a peaky motor.
#62543, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 8
Originally posted by babybeclipse sorry to steal this thread but, What cames work best on a turbo auto trans that revs only to 6500. I'm mainly looking for torque across the board not a peaky motor.
Those #14 should work good
*Skrilla "Honest officer, I thought you were trying to race me" Talon: 1st 2.4L '97 Prelude '04 350Z
Originally posted by YourInMyMirror95GS dick teaser's should be rounded up and shot in the forehead
Originally posted by etx Good luck man! Project 'STFU Brian your talon is dead meat' should be on it's feet soon!
Originally posted by Dark0ne Thanks. Now excuse me while i fuck your sister.
#62584, "RE: What next? #14 turbo cams vs cam gears vs afx udp" In response to Reply # 4
Originally posted by ner947 you'll probably end up wanting something more aggressive than the crane #0014's at some point down the road like crower stage 3's or the crane #0018's.
he doesnt need anything over a 14 unless hes goin all out on the head upgrade, stage 3s and number 18s are worthless and cause nothing more but headaces if you dont have atleast 2 grand invested in the head( major port work, aftermarket valves retainers lifters rockers, os valves etc etc.
DWAYNE H 1996 eclipse under construction widebody eclipse, targa top, 19inch rollers, big brakes, 10 point custom cage, frank 2.4 hrc s20g turbo, custom marble paint job
Search
Printer-friendly copy
1 User in Chat
