I hate to say this... but something has gone seriously wrong. I pulled the wires off the coil and disabled the spark. I hooked up my compression checker and cranked the engine over... number one doesn't read any higher than 60psi. number two came in at 120psi... i didn't check the other two because i was already pissed....
what should i do first, take the head off or drop the oil pan.... any suggestions?? I don't understand what could have caused this... I didn't take her above redline i didn't let her sit at idle at any given time.. and i didn't wrap her out and was pushing only 10psi max and rarely did i ever hit that... she did over heat twice that i can think of when we first started her up... i have a konetic head gasket in there that is supposed to be very nice..... would a spun baring cause low compression??
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
#58518, "FTY motor?" In response to Reply # 0 Oct-13-03 06:08 PM by solareclipse98
Quote:
Originally posted by solareclipse98 I hate to say this... but something has gone seriously wrong. I pulled the wires off the coil and disabled the spark. I hooked up my compression checker and cranked the engine over... number one doesn't read any higher than 60psi. number two came in at 120psi... i didn't check the other two because i was already pissed.... what should i do first, take the head off or drop the oil pan.... any suggestions?? I don't understand what could have caused this... I didn't take her above redline i didn't let her sit at idle at any given time.. and i didn't wrap her out and was pushing only 10psi max and rarely did i ever hit that... she did over heat twice that i can think of when we first started her up... i have a konetic head gasket in there that is supposed to be very nice..... would a spun baring cause low compression??
perhaps a FTY built motor... maybe i will just gut my parts and sell the pistons... im sure they are still good... anyone have anything good to say about FTY?
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
Might be valvetrain, might be bottom end, might be headgasket. You won't know until you pull the head off...
______________________________ If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.
'95 Eclipse TurboGS (garage deco) '95 TSi AWD (restoring a survivor) '97 Talon ESi-T (poor impulse control) '99 Eclipse RS-T (daily beater) '13 Evo X (mostly stock) '17 Sienna (Middle Aged Dad Mobile)
looks like im gonna pull the head off ... fun fun fun...
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
#58549, "sniff sniff sniff? linux btw." In response to Reply # 5
Quote:
Originally posted by Remy Damn man you only had it on the road for such a short time Member # 333
I'm really hoping it's nothing major... the good thing about all this is I have all the other accessories like venom intake and the downpipe is all made the intercooler the turbo all that stuff is fine... my damn engine ... god I knew i shouldn't have trusted rpmrons.com to do it.... they build big motors most the time... I even went easy on the damn thing i don't get it... something was fishy from the start when i only got 150psi when we first put the motor in...
this is just sad ..... i got this bad ass car and a dukey ass engine...
for those who want to follow this project www.dsmpride.com will be back online here in about 3 weeks ... I have ordered a full T1 line to be put into my house.... mainly for the work i do (Software Developer) If anyone want's a place to host their site with decent bandwidth let me know it's a business class t1 line... Id be willing to host a full php/cgi-bin site for $10.00 a month or so.. just in case anyone is interested... for you linux people if you want a shell account let me know as well... i can hook you up...
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
#58554, "RE: sniff sniff sniff? linux btw." In response to Reply # 6
Quote:
Originally posted by solareclipse98 for you linux people if you want a shell account
Yo! over here!
______________________________ If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.
'95 Eclipse TurboGS (garage deco) '95 TSi AWD (restoring a survivor) '97 Talon ESi-T (poor impulse control) '99 Eclipse RS-T (daily beater) '13 Evo X (mostly stock) '17 Sienna (Middle Aged Dad Mobile)
#58555, "RE: sniff sniff sniff? linux btw." In response to Reply # 7
Quote:
Originally posted by DarkOne Quote:
Originally posted by solareclipse98for you linux people if you want a shell account
Yo! over here!
give me a shout on AIM darkone... pgranere21 is my screen name.
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
#58618, "RE: sniff sniff sniff? linux btw." In response to Reply # 10
have you performed a leak-down test? also, id pull the pan first, to see if there is anything obvious like spun bearings or metal shavings. lot easier to pull the pan than the head. goodluck man. 1999 Black C5 1997 Silver RS Wiseco 8.8:1 Pistons(back to low compression!) Eagle Rods T3/T4 Turbo Custom FMIC Greddy Exhaust 390's Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)
#58631, "RE: leak down test" In response to Reply # 11
Originally posted by Nitrous_RS1997 have you performed a leak-down test? also, id pull the pan first, to see if there is anything obvious like spun bearings or metal shavings. lot easier to pull the pan than the head. goodluck man. 1999 Black C5 1997 Silver RS Wiseco 8.8:1 Pistons(back to low compression!) Eagle Rods T3/T4 Turbo Custom FMIC Greddy Exhaust 390's Most current 1/8th mile time: 8.3@90mph 2.015 60'(Nitto Drag radials, i suck)
I'm novice to the leak down... I have already started to take apart the head... at least everything connected to it... i want everything clear out of the way so that i can get it out... can i perform a leak down with the valve cover still off?
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
#58708, "RE: leak down test" In response to Reply # 12
I have this same very problem with my 1G gsx! 85 compression in the 3rd cylinder, and the rest is around 135. I have a feeling its either leaky valves in the head, or it may be warped. It might also be that the rings went bad, but the block is not that old so I'll have to see
#58630, "RE: sniff sniff sniff? linux btw." In response to Reply # 10
Originally posted by Collente Linux... Shell???? hit me up! Nick 97RS turbo8u> shut your SUCK ZAO684: NIPPLE warning...maybe>?
Cool... will do.. I will post an other message when my t1 line gets installed.
- Phil
Formally Project Solar Eclipse Now Entering 300ZX Land.
Jim Wolf ECU w/ Boost Jets Jim Wolf Pop Charger Intake Eibach Pro-Kit Lowering Springs w/ Fully Adjustable Gas Shocks B&B Exhaust - 3" w/ Dual 4.5 Oval Tips w/ 3" Test Pipes Konig Five-O 17X8 Rims w/ Polished Lip Blitz Turbo Timer /w Boost Gauge Freshly Painted Calipers Stillen Unorthodox Pulley Stillen Front Nose / Bumper Stillen Short Shifter New RPS Clutch / Pressure Plate / Flywheel - Holds 550 ft lbs of Torque New Fully-Built 5-Speed Transmission New Howe Radiator w/ 18" Electric Fan w/ Auto Thermostat Controller New Yokohama ES100 Tires All Around New Tension Rods New Fuel Injectors New Spark Plugs New Motor Mounts New Vacuum Hoses New Heater Core New Fuel Filter New Ignition Control Module New Hicas (4-Wheel Steering) Lines New Brake Pads / Brake Lines / Master Cylinder
Search
Printer-friendly copy
1 User in Chat
i wanted to see some good numbers. good luck man
