I am planning on getting a Star kit then getting the FTY 420A Ricekiller 2.0L block. After I have the block in there, my goal is to run 15 psi. Ben over at ImportParts.com e-mailed me this complete list of all the parts that come with the Star stage 2 kit:

Turbonetics T04/T3 Turbocharger
STAR 4 into 1 Cast Iron Turbo Exhaust Manifold
Turbonetics Deltagate Mark II Wastegate
STAR Front Mount Intercooler (Polished Cast Aluminum End Tanks)
HKS Blow-Off Valve
STAR Mandrel-Bent Chrome-Plated Piping
STAR 2.5" Exhaust Down Pipe
STAR Wastegate Dump Tube
STAR Blue Silicone Couplers and Clamps
STAR High Pressure/High Volume Inline Fuel Pump
STAR Vortech Boost Dependent FMU
STAR Intake Air Filter Assembly
Map Sensor Bypass Valves
Stainless Steel Braided Oil Feed Line w/ Fittings
Oil Return Line Assembly
All Necessary Hardware and Fittings
All Necessary Hoses and Hose Clamps
All Necessary Gaskets

I have a few questions for you Star guys:
1) Is this kit supposed to come with the Walbro in-tank?
2) Is the inline pump the Accel pump that everyone says is so loud?
3) Does "Map sensor bypass valves" mean that I should get the Synapse missing link?

I know that I'm going to need bigger injectors and I'm planning on getting the Greddy E-01 when I go to 15 psi, so is there anything that can be left out or anything that I am going to need that I'm not forseeing?

Sorry for the long post guys... I've been saving up and I'm very close to buying the kit now and just don't want to make any mistakes. Thanks for all your help in advance!

>I am planning on getting a Star kit then getting the FTY 420A
>Ricekiller 2.0L block. After I have the block in there, my
>goal is to run 15 psi. Ben over at ImportParts.com e-mailed
>me this complete list of all the parts that come with the Star
>stage 2 kit:
>
>Turbonetics T04/T3 Turbocharger
>STAR 4 into 1 Cast Iron Turbo Exhaust Manifold
>Turbonetics Deltagate Mark II Wastegate
>STAR Front Mount Intercooler (Polished Cast Aluminum End
>Tanks)
>HKS Blow-Off Valve
>STAR Mandrel-Bent Chrome-Plated Piping
>STAR 2.5" Exhaust Down Pipe
>STAR Wastegate Dump Tube
>STAR Blue Silicone Couplers and Clamps
>STAR High Pressure/High Volume Inline Fuel Pump
>STAR Vortech Boost Dependent FMU
>STAR Intake Air Filter Assembly
>Map Sensor Bypass Valves
>Stainless Steel Braided Oil Feed Line w/ Fittings
>Oil Return Line Assembly
>All Necessary Hardware and Fittings
>All Necessary Hoses and Hose Clamps
>All Necessary Gaskets
>
>I have a few questions for you Star guys:
>1) Is this kit supposed to come with the Walbro in-tank?
>2) Is the inline pump the Accel pump that everyone says is so
>loud?
>3) Does "Map sensor bypass valves" mean that I should get the
>Synapse missing link?
>
>I know that I'm going to need bigger injectors and I'm
>planning on getting the Greddy E-01 when I go to 15 psi, so is
>there anything that can be left out or anything that I am
>going to need that I'm not forseeing?
>
>Sorry for the long post guys... I've been saving up and I'm
>very close to buying the kit now and just don't want to make
>any mistakes. Thanks for all your help in advance!

Yes the fuel pump is loud, but after a month you won't even notice it anymore. The walbro was an upgrade in Wyatt's kits, it may be the same with this company so I would ask if you really want it. I run the star inline though and it's all the pump you need. Plus when you up your injects you won't need high pressures anymore. If "Map sensor bypass valves" means the electronic box then I would get the missing link, because it's pretty much fool proof. If that is a manual valve unit then you could prolly keep it. I would say do some more reasearch on your fuel system before you decide on the E01/ emanage combo. You will also need an exhaust upgrade, so i would do it right the first time and get a 3" cat back.

I edited to the wiki!