it already came out once on me (durf). i fixed it really good this time, but I still have annoying exhaust leaks. the car sounds like a grass cutter at idle. i clamped that damn thing down as best i could. how can i make this better.. i would like to weld it, but maybe there is a simpler solution... hellllppp............ they couldn't just give us a real dp....grr

thanks

man i have that same problem and noise..i only have one nut holding my downpipe to the manifold....very bad leak!

SoCal DSM
1996 RS-T: Under Construction
1999 GS AE: New daily driver
"USING NO WAY AS A WAY, HAVING NO LIMITATION AS A LIMITATION"--BRUCE LEE

yea, mine is bad too, even with the clamp. im waiting for a good deal on a 2.5"-3" bolt on downpipe... much like a lot of other people.

______________________________
Matt D.
'06 Evo IX SE
'98 RS-T 13.8 @ 106.1

Yeah, the HRC DP connection is pretty ghetto. I also had the crappy leak, but I pretty much fixed most of mine. I took it apart, and tried to round out both pipes as good as possible, then got a 2" exaust clamp just barely on there..It worked believe it or not, and clamped it good. The biggest problem from what i can tell, is that HRC gives you a 2.25" clamp, and our exaust pipe is slightly smaller, and when you tighten it, clamps the piping not evenly all around the pipe, causeing the pipe to "sqeeze" at the edges in a way, so you have gaps, kinda like () . Mine is just about leak free, and i cant hear any leaks at all. I've still had enough of it though, cause i can tell that stock DP is not flowing well at 13 psi. I'm tired of waiting for 2.5" pipes to come out, so I am going to buy some mandrel bends, fab it, cut it, and piece it together myself, then have it professionally welded at a welding shop out here..

13.5 @108 MPH-2.2 60ft(stupid FWD!)
S16G @ 18 PSI/FMIC/Running on MegaSquirt II (Now with sequential
fuel injection)
My webpage: http://eclipsed4evr.home.comcast.net
-1998 Mitsubishi Eclipse RS-T- "Toy"
-1992 Plymouth Laser Turbo AWD(SOLD)
-2000 Honda CR-V(daily)

W3rd on the ghetto DP...POS IMO

__________________________________________
~Chris
03 SRT-4

I got a generic straight through muffler from a shop and took it to this exaust place. I had the guy install a fitting on the hrc dp so i could unscrew it from the rest of the exaust. and he did 2.5 inch mandrel bent pipes all the way back to the new muffler with a flex section and with both o2 sensors in there for $250. total cost for exaust ~$350 and it sounds great, and no leaks!!

____________________________________________________
four nails four corners four riders and four horses

I'm having a this guy who has his own shop make me a new one piece dp. He's making one for my friends RX-7 for $200. Figure one for an Eclipse cant be much more. I'd like to get it done before the Raceway Park meet on the 14th but its coming up real fast.

Mine is welded and it's a mighty good job if I say so. Don't know what it cost cause I got it all done and included in my install. My only complaint is the bolt bracket that holds the actual pipe to the frame. That must have flexed under launching and broke off once and it's coming undone again. But no leaks here..


http://www.cardomain.com/id/jasvbts2k2
"The ONLY Honda I'd mod would be ASIMO"

I got mine taken care of by getting a section of 2.5" and had it welded on to the HRC pipe and then that is mandrel bent and goes under the car, eliminates the cat and runs straight back. So know from the bottom of the HRC pipe I'm running straight back now. I like the setup and it did make a good difference.

I just did another Stage II install and he has had no probs with leaks on the downpipe. I just made sure it was cut far enough up and tightened it up really good. I made sure to leave enough on the stock to have it fit in tight. I'm surprised nobody has made a downpipe yet, dosn't look like it would be too hard with the right tools.

'00 Harley-Davidson F150
'88 Mustang GT
'93 Mustang LX 5.0
'00 Focus (beater)

I had mine welded on. I use to have Kamikazi headers and it came with a downpipe. I had a muffler shop cut the downpipe a little shorter and weld the HRC DP onto it. It fit really great and I've had no leaks.

i'm about to finish mine up once i can walk again.... if i get it welded off the car will it slip up in easy or will it be a pain in the ass if i do it this way..........

2006 WW IX MR
2003 BBY EVO VIII (sold)
256.9WHP & 277.9torque
http://s90395832.onlinehome.us/forum//index.php?sid=a70942a7f65043e6c873e12dcd300692

1998 Eclipse RS --show car--

I believe you should get it done on the car. You have to make sure every thing lines up. It cost me $20 to get it done on the car and only took 5 min.



1998 Eclipse GS,Hahn Stage 2 Turbo Kit w/ Missing Link and Vortech SFMU,TurboXS Type H RFL, Turbo XS HP Boost Controller, Corbins Digital A/F Gauge,Apex N1 Exhaust,Autometer Gauges

I completely agree, mine sounds like a lawn mower too and I can actually feel the exhuast gas on my hand coming up through the engine bay. I'm not real thrilled about all that hot exhuast gas in my engine bay ... let alone it being sucked back in buy the filter. Anyway, I have a question for guys that had it welded. Did you cut the stock DP so that they just barely came together, or did you leave a bunch on there up inside the HRC end and then have it welded. I'm thinking for exhuast flow it would be better to cut it down farther and then have it welded, but I'm not sure it matters ..... anybody?


Yes officer, the windows are mirrored!

HRC Stage II w/FMIC

i figured i'd put it together with the flanges make it fit nice and straight and then take it to get welded.......

2006 WW IX MR
2003 BBY EVO VIII (sold)
256.9WHP & 277.9torque
http://s90395832.onlinehome.us/forum//index.php?sid=a70942a7f65043e6c873e12dcd300692

1998 Eclipse RS --show car--

i had my HRC/stock downpipe thing brazed. the guy who did it didn't exactly do such a great job. it still leaks a little, but it's a lot better than before. i didn't want to do anything nuts, because i've been waiting for the ERT downpipe. however, by now i'm pretty convinced that it'll never actually be released, so i'm looking to get some mandrel bends and some custom exhaust work done.

2016 WRX STi Limited (current)
2001 A4 1.8tqms (donated)
1991 GVR4 #1933 (sold)
old.dsmregistry.com/detail.php?carid=218 (dismantled)

I just left a bunch up in there techboy. I wish I would of had it cut to match though. Your idea on flow is probably right. I probably gona have a custom 2.5 to 3 inch made soon. Seems like no one wants to make us a full down pipe right now.



1998 Eclipse GS,Hahn Stage 2 Turbo Kit w/ Missing Link and Vortech SFMU,TurboXS Type H RFL, Turbo XS HP Boost Controller, Corbins Digital A/F Gauge,Apex N1 Exhaust,Autometer Gauges