#2035, "Injectors - I know its well discussed, but can someone show me how to calculate which ones I need?"
I know its well discussed, but can someone show me how to calculate which injectors I need?
HRC Tubro Kit Stage 2 with FMIC APEX'i Intercooler 9.5:1 JE Pistons, Crower Rods I have a SAFC and the Fuel Pressure Regulator that came with the Kit.
So far, I was running my SAFC 20% Lean across the band @ a fuel pressure of 90-100psi (under boost) at 10psi Boost for a perfect A/F mixture. All of this on Stock injectors with the biggest baddest Holley (Walbro) intank fuel pump.
As I have kept my compression ratio roughly the same, I figure that with the boost turned up to about 16-18psi my stock fuel injectors can still handle it. Very Riskily though - I know.
That's why I want new injectors, and I would like to know any formulae or ideas/tips on how to calculate what I need, and what I might ever need...
Also could someone explain why I would ever need an aftermarket ECU for controlling injectors...
Thanks guys,
Guy RS_Guy
13.9sec @ 105mph passes w/ Blown piston rings, on Stock Internals at 10psi Boost....
The only reason you'd need a seperate computer to control your injectors is if you have the need to run something SO LARGE that the combination of the SAFC and the stock ECU just can't handle it... Like 700cc/min injectors
-DarkOne I'm so bad, i should be in detention.
______________________________ If a sentence found online has 35% misspellings or greater and includes at least two racially charged expletives, chances are it is a YouTube comment.
'95 Eclipse TurboGS (garage deco) '95 TSi AWD (restoring a survivor) '97 Talon ESi-T (poor impulse control) '99 Eclipse RS-T (daily beater) '13 Evo X (mostly stock) '17 Sienna (Middle Aged Dad Mobile)
#2040, "RE: Injectors - I know its well discussed, but can someone show me how to calculate which ones I nee..." In response to Reply # 4
At 10psi the engine was holding up to boost just fine, until at the track, some blow-by poured all the oil out of my engine.
It seems that lots of us seem to have problems with blow-by on stock engine internals. What exactly causes this, I dunno.. My car had about 95K miles before boosting...
Guy RS_Guy
13.9sec @ 105mph passes w/ Blown piston rings, on Stock Internals at 10psi Boost....
#2041, "RE: Injectors - I know its well discussed, but can someone show me how to calculate which ones I nee..." In response to Reply # 5
So, your running a Walbro in-tank fuel pump, and still leaning back the to get a good Air/fuel? I new it ran rich,, just didn't know htat much I'm running about .96+v @ 7psi of boost. I haven't trimmed out the AFC yet. man I'm lazy Wyatt Leras http://www.turbogs.com 98 Eclipse GS Star Stage 5,000 Turbo kit
#2042, "RE: Injectors - I know its well discussed, but can someone show me how to calculate which ones I nee..." In response to Reply # 6
LAST EDITED ON 01-Mar-01 AT 12:57 PM (PST)
OK, looking back at the receipt for my fuel pump...
It is a Holley (a repackaged Walbro) and yes I overpayed for the "name", but I needed it pronto. I don't have the regular 255lph in-tank. I ordered Model #12-918 "255 LPH Forced Induction".
This is what Holley Has to say about it:
New this year are 255 liter-per-hour-rated "forced induction" pumps. These new pumps flow significantly more fuel at higher pressure. For example, at 80 PSI the standard 255 lph pump will flow around 132 liters (35 gallons) per hour. At that same 80 PSI the equivalent forced induction fuel pump will flow over 210 liters (50 gallons) per hour.
I'd call it a good deal, considering it cost pretty much the same as the "regular 255LPH".
Search
Printer-friendly copy
1 User in Chat
