well sorry if this is a stupid question but im kinda excited bout the install. well lets see i wanted to know about how long it would take to install the kit and the exhaust. i have the fuel pump,exhaust manifold,downpipe,intake,muffler, and oil pan off. and dan will be coming so he has done this b4. does anybody have anyidea how long it will take? and another question. is it ok to use my old bolts? they look kinda rusted but they dont look like they have been streched past there elastic limit. TIA later

o and if i wanted knew bolts, does satan sell them?


"Proud to be, a 2gnt"


-mitsuman

Performance:
1. AEM cold air intake
1. NGK plugs

Ride:
1. motegi mr7 17'' wrapped
in yokohama A550v
235/45/17

Sound:
1. sony xplod cdxm620 deck
2. 2 10'' audiobahn subs
3. nice shiny audiobahn
amp

In room:
1. blitz front end(thnx 2
eclipse804)
2. H&R sport springs(thnx 2
eclipse804)

Fun mods:
1. "Nozzel mod"

Wanted:
1. to much ish to list... but a
boy can dream

in the mail:
1. HRC STG 2
2. Greddy Power Extreme
3. Blits Super Sound BOV
4. HKS Turbo timer

-mitsuman 95 GS 5-spd w/97-99 front end
Repin The SoCal 2GNT'ers
mitsuman95@hotmail.com
AIM s/n : mitsuman95gs

since you did all of the hard work for Dan and I by removing all of the stock componente (I hope you did not remove the fuel pump as we need it.), I'm sure between the 3 of us...not more than 8 hour...I hope we'll see. it will be a learning experience. You have the teflon paste right?


kaiser

-K-

put it this way...it took me 24 (i added them up) hours out of a 48 hour period.

http://home.bendcable.com/optimuspeterson <<<<HRC Stage 2 and Star Instructions
95 Eclipse - SOLD | 93 BMW 318is - SOLD | 2000 S-10 Extreme on 20's - SOLD
93 Toyota/shaved/bagged/body dropped - SOLD | 97 GSX - SOLD
2006 Scion tC

damm thats a long ass time. well were actually allmost done. worked for about six hours today . should get done by tomorrow. dan (thedawg) and kaiser (eclipsekaiser) came by and helped out. i think they helped out A LOT. omg it would have takin me forever to read the instructions over and over and to figure that shit out. thnx guys for the help.


"Proud to be, a 2gnt"


-mitsuman

Performance:
1. AEM cold air intake
1. NGK plugs

Ride:
1. motegi mr7 17'' wrapped
in yokohama A550v
235/45/17

Sound:
1. sony xplod cdxm620 deck
2. 2 10'' audiobahn subs
3. nice shiny audiobahn
amp

In room:
1. blitz front end(thnx 2
eclipse804)
2. H&R sport springs(thnx 2
eclipse804)

Fun mods:
1. "Nozzel mod"

Wanted:
1. to much ish to list... but a
boy can dream

in the mail:
1. HRC STG 2
2. Greddy Power Extreme
3. Blits Super Sound BOV
4. HKS Turbo timer

-mitsuman 95 GS 5-spd w/97-99 front end
Repin The SoCal 2GNT'ers
mitsuman95@hotmail.com
AIM s/n : mitsuman95gs

So how is the install going? you only have about 3 other thing left.

Did you two manage to get the oil sensor off of the block?

No problem of the install. I just wish we started a little earlier so that we might have been able to finish it.

Do not forget to teflon paste or tape the oil sender on the back of the block like I said. For your fuel gauge, I would highly reccomend the paste.

let me know if Dan and I can help you out in any other way. Just drop us an email, or post on this board.

Good luck.

kaiser

-K-

He still needs:
- Weld the muffler right (I've got an RS muffler he can use)
- Get a fuel gauge & connect
- Get & connect vacuum lines to BOV
- Get a check valve for FPR (prolly gonna use a fishtank one)
- Get the oil sender teed off
- Replace PCV and crankcase breather hoses
- Finish hooking up intercooler piping
- Take snorkel off the downpipe