is there a trick to bondo? the issue im having is where im putting it on and than sanding it seems as if the bondo is crumbling like it will sand smooth but in areas it will be pitted and have holes and in some areas it will be smooth. i go back over it with a smooth coat of bondo and let it dry and sand again and the same crap? am i not mixing it right or what am i doing wrong or does bondo just flat out suck? im using it to finnish off some of the lines on my car like where the side skirts meet the fenders and stuff like that. thanks in advance
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

I'm no where near an expert on body work, but it sounds like you might be mixing it a little to much, thus getting more air pockets in there when you apply it.

DSM= Doesn't Start Monthly

your over hardening it . a good trick to mixing it is to put a small line of hardener across the diameter of bondo your mixing .do not just mix it either . you have to keep like folding it and mashing it till its one color .

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

got ya yeah i figured i was doing that wrong i was mixing it like pancake batter only thicker lol, ill give that a try
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

Peace,
The statements regardin' the amount of hardner and the way you mix it is tru, but it can also be the quality of the bondo itself... The type from Wal-Mart for instance isn't good... Check this out... I was given this link from optikal... I purchased it, I haven't had the time to use it yet, but this is Official quality... Somewhat pricey and may not interest you because of what you're usin' it for, but if you want the quality, this is it...

http://www.autotoolmart.com/cgi-bin/webc.cgi/st_prod.html?p_prodid=10886&p_catid=63


Peace,
Jem

i got the expensive stuff its blue and like some ultimate crap or something sappose to be like super light weight?? i dont know i just wanted to fill in where my skirts meet my fenders give it that finnished 1 piece look ya know. anyway i did what was posted before and so far so good i got a good clean smooth surface at 3 points all i have to do is work on the 4th and im good to go but thanks for the imput
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

you know its funny you mentioned that because when i couldnt get it to smooth out compleetly i used some bondo glazing putty and now its smooth as a babys azz, that stuff works alot better at filling in. thanks
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

the seam will crack out unless you glued the sideskirt to the fender with duramix or fusor or any other of a number of autobody adhesives. after it's glued you want to use a fiberglass reinforced filler like mar-glass and THEN do your bondo work on top of that.

_______________________

-eric stratton
Kustom Auto Koatings
North East, Md
443-528-8007
http://www.kustomautokoatings.com

how about liquid nails? when i originally put them on i never intended on taking them off and used liquid nails at the seams, seemed to hold pretty well, if not than i think it might be back to the drawing board, thanks for the help though.

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed

i would use fusor 142 . i dont think liquid nail will hold up

LED tails : Done for now!
99 eclipse rst
cobalt blue met. paint,star stage 2 upgraded t3/t460trim turbo ceramic coated , polished compressor housing, ,optima yellow top, chrome i/c piping ,front mount ntercooler ,apexi turbo timer . zeitronix wb02 ,faze oil ,boost gauge,egt ,bosch 4x plugs,kyb agx struts, pro kit springs.17''adr venomous rims,Falken azenis ,brembo dilled/slotted rotors ,turbo xs bov ,oil catch can,manual shiftknob,autometer pyrometer egt , vortech sfmu,b&m fuel pressure gauge ,accel 310cc injectors ,gasketmatched and polished intake manifold ,58mm throttle body ,no egr,polished turbonetics wastegate,fuel pump rewire,homade fcd and a lot more .LED reverse lights ,sidemarkers and tails .atx to mtx swap . South bend tz clutch . Tons more
http://imageshack.us>


http://www.2gnt.com/index.php?d=boosted60trimrst
My contribution to the wiki
http://www.2gnt.com/index.php?d=crank%20arm%20spindle%20mod%20to%20fit%20power%20panels

yea I don't know about the liquid nails. my kit is molded using UPOL 904 adhesive which is the equivalent to the fusor and the duramix. it's been molded for a few years now with no cracking whatsoever. it is also what is holding my mr2 vents in the quarter's.

_______________________

-eric stratton
Kustom Auto Koatings
North East, Md
443-528-8007
http://www.kustomautokoatings.com

i guess i will have to take my chances the car is done now sanded and primed, everything is smooth and flawless i guess if i get cracks if nothing else i learned a little about body work and can do it better next time. thanks to everyone who replied
joe

98 RS: Mods: Custom Stage 2 Turbo kit , 55mm throttle body, gutted cat, evo cat back exhaust, p/p intake manifold,p/p Head, af-x underdrive pulley, B&M short throw shifter,Built bottom end Je pistons eagle rods 8.8:1 compression.





Status:Up and running again! nice new paint

Custom stage 2 hahn turbo kit
Hahn Super 16g turbo (ceramic coated)
Hahn manifold (ceramic coated)
Hahn Downpipe assembly
Hahn intercooler piping smic
Hahn oil line kit
Type s bov
2G Gsx smic
walbro 255 fuel pump
Synapse missing link
Vortech s-fmu
NGK Bkr7e11 Plugs
A-pillar w/boost, a/f, oil pressure gauges


New Addition: 2007 Eclipse GT 6 speed